upd78f0114m6gb-8es Renesas Electronics Corporation., upd78f0114m6gb-8es Datasheet - Page 396
upd78f0114m6gb-8es
Manufacturer Part Number
upd78f0114m6gb-8es
Description
8-bit Single-chip Microcontrollers
Manufacturer
Renesas Electronics Corporation.
Datasheet
1.UPD78F0114M6GB-8ES.pdf
(534 pages)
- Current page: 396 of 534
- Download datasheet (5Mb)
23.5.3 RESET pin
signal generator on the board, signal collision takes place. To prevent this collision, isolate the connection with the
reset signal generator.
memory will not be correctly programmed. Do not input any signal other than the reset signal of the dedicated flash
programmer.
23.5.4 Port pins
same status as that immediately after reset. If external devices connected to the ports do not recognize the port
status immediately after reset, the port pin must be connected to V
23.5.5 Other signal pins
inverse signal to X2.
23.5.6 Power supply
the V
GND of the flash programmer.
396
If the reset signal of the dedicated flash programmer is connected to the RESET pin that is connected to the reset
If the reset signal is input from the user system while the flash memory programming mode is set, the flash
When the flash memory programming mode is set, all the pins not used for flash memory programming enter the
Connect X1 and X2 in the same status as in the normal operation mode when using the on-board clock.
To input the operating clock from the programmer, however, connect the clock out of the programmer to X1, and its
To use the power supply output of the flash programmer, connect the V
However, the flash programmer is used to monitor voltage, be sure to connect the V
To use the on-board power supply, connect in compliance with the normal operation mode.
Supply the same other power supplies (EV
SS
pin to V
SS
of the flash programmer.
µ
PD78F0114
RESET
In the flash memory programming mode, the signal output by the reset
signal generator collides with the signal output by the dedicated flash
programmer. Therefore, isolate the signal of the reset signal generator.
Figure 23-16. Signal Collision (RESET Pin)
Signal collision
DD
CHAPTER 23
User’s Manual U16227EJ3V0UD
, EV
SS
, AV
Reset signal generator
REF
Dedicated flash programmer
connection pin
, and AV
PD78F0114
Output pin
DD
or V
SS
) as those in the normal operation mode.
SS
DD
via a resistor.
pin to V
DD
of the flash programmer, and
DD
and V
SS
pins to V
DD
and
Related parts for upd78f0114m6gb-8es
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Renesas Technology Corp [Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series]
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
RENESAS MCU M16C FAMILY / M16C/Tiny SERIES
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas Starter Kit for RX210
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas StarterKit for RX630
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit+ for RX63N
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
FLASH PROGRAMMER FOR RENESAS MICROCONTROLLERS
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet: