sm5301a Nippon Precision Circuits Inc, (NPC), sm5301a Datasheet
sm5301a
Available stocks
Related parts for sm5301a
sm5301a Summary of contents
Page 1
... OVERVIEW The SM5301AS is a video buffer with built-in video signal bandwidth lowpass filter. The filter employs a 5- order Butterworth lowpass filter configuration. The filter characteristics have been optimized for minimal over- shoot and flat group delay, it has a variable cutoff frequency and guaranteed driver-stage channel gain differ- ence and phase difference values ...
Page 2
... R /Y INB INB G /U INA INA MUX G /U INB INB B /V INA INA MUX B /V INB INB MUXSEL SYNCIN GND1 SM5301AS VCC2 VCC3 VCC4 LPF DC Restore LPF DC Restore LPF DC Restore GND2 GND3 GND4 Buffer R /Y OUT OUT GSR1 Buffer G /U OUT ...
Page 3
... I INA INA 26 GSR1 INB INB 28 NC – SM5301AS Description Analog signal input. Sync signal is input on SYNCIN pin. INA INA G /U output buffer gain set input OUT OUT Analog signal input. Sync signal is input on SYNCIN pin. INB ...
Page 4
... When mounted on a substrate: mounted on a 111 × 80 × 1.6mm glass-epoxy substrate with 90% copper (Cu) wiring factor, 0m/s air flow, and ° C. Recommended Operating Conditions Parameter Symbol Supply voltage ranges V CC Operating temperature range Ta SM5301AS Rating Unit − 0.3 to 7.0 V − 125 ° C 1.0 W 0.9 ...
Page 5
... IL1 Logic HIGH-level input voltage 2 V IH2 Logic LOW-level input voltage 2 V IL2 Logic pull-up resistance R IN2 Logic pull-down resistance R IN3 SM5301AS Condition min = 5.5V, RFC = 820 Ω to GND VFC = 0.2V (fc = 5MHz), 70 DISABLE = "L" = 5.5V, RFC = 820 Ω to GND VFC = 1.6V (fc = 40MHz), 90 DISABLE = " ...
Page 6
... II : Guaranteed as result of design and characteristics evaluation 0.0 0.2 SM5301AS Condition Ta=25°C (see figure 25° 5.0V CC fIN ≥ 4fc 10kHz to 40MHz, 6dB output gain setting Between 2 channels with input 0.5Vp-p 1MHz Between MUX A−B Each input = 500kHz to 3.58MHz ...
Page 7
... SM5301AS 2.00E+01 0.00E+00 –2.00E+01 –4.00E+01 –6.00E+01 –8.00E+01 1.00E+03 1.00E+04 1.00E+05 Frequency [Hz] Figure 2. Frequency response (VFC = 0.2V) 2.00E+01 0.00E+00 –2.00E+01 –4.00E+01 –6.00E+01 1.00E+03 1.00E+04 1.00E+05 Frequency [Hz] Figure 3. Frequency response (VFC = 1.0V) 2.00E+01 0.00E+00 -2.00E+01 -4.00E+01 1.00E+03 1.00E+04 1 ...
Page 8
... 5.0V, 32% duty drive DD Note: The resistor connected to RFC can affect the cutoff frequency response high-precision component should be used recommended to set the RC filter cutoff frequency to < fc/100 of the PWM wave- form frequency. SM5301AS VR VFC VFC R1 VFC C1 RFC ...
Page 9
... The VFC voltage can be controlled using multi-logic voltage levels switching inputs to a voltage divider resis- tor network The VFC voltage is determined by the logic voltage (V1, V2, V3) and the corresponding voltage divider resis- tor network. SM5301AS VFC RFC R0 SEIKO NPC CORPORATION —9 ...
Page 10
... GND pin. Input Capacitor and Cutoff Frequency The capacitor connected to pins R forms a highpass filter (HPF) with the internal impedance. The HPF cutoff frequency is given by the following equation 2πCR (C: input capacitance, R: signal input impedance = 9.3kΩ) SM5301AS Cut-off (*2) (*1) (* ...
Page 11
... G OUT OUT R /Y OUT OUT Digital TV Receiver and HDTV Decoder Box MPEG2 Decoder/Display Transport/Decoder Video Decoder CAMERA Display Processor DVD-ROM MEMORY SM5301AS / OUT OUT OUT 220µF 75Ω + 75Ω Graphic Processor HDTV Convertor Processor ...
Page 12
... Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. SM5301AS SEIKO NPC CORPORATION 15-6, Nihombashi-kabutocho, Chuo-ku, ...