ad5323bru-reel Analog Devices, Inc., ad5323bru-reel Datasheet - Page 15

• Manufacturer Part Number: ad5323bru-reel
• Description: 2.5 V To 5.5 V, 230 ?a, Dual Rail-to-rail Voltage Output 8-/10-/12-bit Dacs
• Manufacturer: Analog Devices, Inc.

FUNCTIONAL DESCRIPTION
The AD5303/AD5313/AD5323 are dual resistor-string DACs
fabricated on a CMOS process with resolutions of 8-/10-/12-bits
respectively. They contain reference buffers and output buffer
amplifiers, and are written to via a 3-wire serial interface. They
operate from single supplies of 2.5 V to 5.5 V and the output
buffer amplifiers provide rail-to-rail output swing with a slew
rate of 0.7 V/μs. Each DAC is provided with a separate reference
input, which may be buffered to draw virtually no current from
the reference source, or unbuffered to give a reference input
range from GND to V
power-down modes, in which one or both DACs may be turned
off completely with a high impedance output, or the output may
be pulled low by an on-chip resistor.
DIGITAL-TO-ANALOG
The architecture of one DAC channel consists of a reference
buffer and a resistor-string DAC followed by an output buffer
amplifier. The voltage at the V
voltage for the DAC. Figure 29 shows a block diagram of the
DAC architecture. Because the input coding to the DAC is
straight binary, the ideal output voltage is given by
where:
D is the decimal equivalent of the binary code, which is loaded
to the DAC register:
N is the DAC resolution.
0 to 255 for AD5303 (8 bits)
0 to 1023 for AD5313 (10 bits)
0 to 4095 for AD5323 (12 bits)
REGISTER
INPUT
V
OUT
=
V
Figure 29. Single DAC Channel Architecture
REF
2
REGISTER
N
×
DAC
D
DD
REFERENCE
. The devices have three programmable
BUFFER
REF
RESISTOR
STRING
pin provides the reference
V
REF
A
OUTPUT BUFFER
AMPLIFIER
SWITCH
CONTROLLED
BY CONTROL
LOGIC
V
OUT
A
Rev. B | Page 15 of 28
RESISTOR STRING
The resistor string section of the AD5303/AD5313/AD5323
is shown in Figure 30. It is simply a string of resistors, each of
value R. The digital code loaded to the DAC register determines
at what node on the string the voltage is tapped off to be fed
into the output amplifier. The voltage is tapped off by closing
one of the switches connecting the string to the amplifier.
Because it is a string of resistors, it is guaranteed monotonic.
DAC REFERENCE INPUTS
There is a reference input pin for each of the two DACs. The
reference inputs are buffered, but can also be configured as
unbuffered. The advantage with the buffered input is the high
impedance it presents to the voltage source driving it. However,
if the unbuffered mode is used, the user can have a reference
voltage as low as GND and as high as V
restriction due to headroom and footroom of the reference
amplifier.
If there is a buffered reference in the circuit (for example,
REF192), there is no need to use the on-chip buffers of the
AD5303/AD5313/AD5323. In unbuffered mode, the input
impedance is still large at typically 180 kΩ per reference input
for 0 V to V
The buffered/unbuffered option is controlled by the BUF A
and BUF B pins. If a BUF pin is tied high, the reference input
is buffered; if tied low, it is unbuffered.
OUTPUT AMPLIFIER
The output buffer amplifier is capable of generating output
voltages to within 1 mV of either rail, which gives an output
range of 0.001 V to V
It is capable of driving a load of 2 kΩ in parallel with 500 pF to
GND and V
amplifier can be seen in Figure 17.
The slew rate is 0.7 V/μs with a half-scale settling time to
±0.5 LSB (at eight bits) of 6 μs.
REF
DD
. The source and sink capabilities of the output
mode and 90 kΩ for 0 V to 2 V
R
R
R
R
R
DD
Figure 30. Resistor String
− 0.001 V when the reference is V
AD5303/AD5313/AD5323
TO OUTPUT
AMPLIFIER
DD
since there is no
REF
mode.
DD
.