s29gl128n Meet Spansion Inc., s29gl128n Datasheet - Page 74

• Manufacturer Part Number: s29gl128n
• Description: 3.0 Volt-only Page Mode Flash Memory Featuring 110 Nm Mirrorbit ?rocess Technology
• Manufacturer: Meet Spansion Inc.

Notes:
1. DQ5 switches to 1 when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for
3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location.
4. DQ1 switches to 1 when the device has aborted the write-to-buffer operation
72
Standard
Write-to-
Suspend
Suspend
Program
Buffer
maximum timing limits. Refer to the section on DQ5 for more information.
further details.
Mode
Mode
Erase
Mode
DQ3: Sector Erase Timer
DQ1: Write-to-Buffer Abort
Embedded Program Algorithm
Embedded Erase Algorithm
Erase-Suspend-Program 
(Embedded Program)
Busy
Abort
Program-
Suspend
Suspend
Erase-
Read
Read
After writing a sector erase command sequence, the system may read DQ3 to determine
whether or not erasure has begun. (The sector erase timer does not apply to the chip erase
command.) If additional sectors are selected for erasure, the entire time-out also applies after
each additional sector erase command. When the time-out period is complete, DQ3 switches
from a 0 to a 1. If the time between additional sector erase commands from the system can
be assumed to be less than 50 µs, the system need not monitor DQ3. See also
Command Sequence‚ on page
After the sector erase command is written, the system should read the status of DQ7 (Data#
P olling) or DQ6 (T oggle Bit I) to ensure that the device has accepted the command sequence,
and then read DQ3. If DQ3 is 1, the Embedded Erase algorithm has begun; all further com-
mands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is 0,
the device accepts additional sector erase commands. To ensure the command is accepted,
the system software should check the status of DQ3 prior to and following each subsequent
sector erase command. If DQ3 is high on the second status check, the last command might
not have been accepted.
T able 16 on page 72
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1
produces a 1. The system must issue the Write-to-Buffer-Abort-Reset command sequence to
return the device to reading array data. See
(Note 3)
(Note 4)
Status
Program-Suspended
Sector
Non-Program
Suspended Sector
Erase-Suspended
Sector
Non-Erase
Suspended Sector
shows the status of DQ3 relative to the other status bits.
Table 16. Write Operation Status
S29GL-N MirrorBit™ Flash Family
(Note 2)
57.
DQ7#
DQ7#
DQ7#
DQ7#
DQ7
0
1
D a t a
No toggle
Toggle
Toggle
Toggle
Toggle
Toggle
DQ6
Write Buffer‚ on page 14
S h e e t
Invalid (not allowed)
(Note 1)
DQ5
0
0
0
0
0
0
Data
Data
DQ3
N/A
N/A
N/A
N/A
N/A
1
No toggle
(Note 2)
for more details.
Toggle
Toggle
DQ2
N/A
N/A
N/A
S29GL-N_00_B3 October 13, 2006
Sector Erase
DQ1
N/A
N/A
N/A
0
0
1
RY/BY#
0
0
1
1
1
1
0
0
0