adv7120kn80 Analog Devices, Inc., adv7120kn80 Datasheet
adv7120kn80
Related parts for adv7120kn80
adv7120kn80 Summary of contents
Page 1
... PLCC. The ADV7120 is also available in a very small 48- lead Thin Quad Flatpack (TQFP). ADV is a registered trademark of Analog Devices, Inc. *Speed grades up to 140 MHz are also available upon special request. Please contact Analog Devices or its representatives for further details. ...
Page 2
ADV7120–SPECIFICATIONS Parameter STATIC PERFORMANCE Resolution (Each DAC) Accuracy (Each DAC) Integral Nonlinearity, INL Differential Nonlinearity, DNL Gray Scale Error Coding DIGITAL INPUTS Input High Voltage, V INH Input Low Voltage, V INL Input Current Input Capacitance, C ...
Page 3
TIMING CHARACTERISTICS Parameter 80 MHz Version 50 MHz Version MAX 12 ...
Page 4
... B5 NOTE For the ADV7120 in TQFP package: The REF WHITE pin is not available. The I pin is not available and is internally connected to the IOG pin. SYNC Typ Max Units Model 5.00 5.25 Volts ADV7120KN80 +70 C ADV7120KN50 ADV7120KN30 37.5 ADV7120KP80 1.235 1.26 Volts ADV7120KP50 ADV7120KP30 ADV7120KST50 50 MHz +0.5 V ADV7120KST30 30 MHz ...
Page 5
Pin Mnemonic Function BLANK Composite blank control input (TTL compatible). A logic zero on this control input drives the analog out- puts, IOR, IOB and IOG, to the blanking level. The BLANK signal is latched on the rising edge of ...
Page 6
ADV7120 TERMINOLOGY Blanking Level The level separating the SYNC portion from the video portion of the waveform. Usually referred to as the front porch or back porch IRE units the level which will shut off the ...
Page 7
If we, therefore, have a graphics system with a 1024 1024 resolution, a noninterlaced 60 Hz refresh rate and a retrace fac- tor of 0.8, then: Dot Rate = 1024 1024 60/0.8 = 78.6 MHz RED, BLUE GREEN mA V ...
Page 8
ADV7120 A resistance R connected between FS ADJUST and GND SET determines the amplitude of the output video level according to the following equations: IOG (mA) = 12,082 V (V)/R REF SET IOR, IOB (mA) = 8,628 V (V)/R REF ...
Page 9
The unused analog outputs should be terminated with the same load as that for the used channel. In other words, if the red channel is used and IOR is terminated with a doubly terminated 75 load (37.5 ), IOB and ...
Page 10
ADV7120 PC BOARD LAYOUT CONSIDERATIONS The ADV7120 is optimally designed for lowest noise perfor- mance, both radiated and conducted noise. To complement the excellent noise performance of the ADV7120 imperative that great care be given to the PC ...
Page 11
Power Planes The PC board layout should have two distinct power planes, one for analog circuitry and one for digital circuitry. The analog power plane should encompass the ADV7120 (V sociated analog circuitry. This power plane should be connected to ...
Page 12
ADV7120 0.045 TYP 0.17 (4.32) MAX 0.021 (0.533) 0.015 (0.381) 0.004 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 44-Terminal Plastic Leaded Chip Carrier (P-44A) 0.045 TYP 0.045 TYP PIN 1 IDENTIFIER 0.045 ...