mc33293atv Freescale Semiconductor, Inc, mc33293atv Datasheet
mc33293atv
Related parts for mc33293atv
mc33293atv Summary of contents
Page 1
... Short Circuit Detection and Shutdown with Automatic Retry ORDERING INFORMATION Operating Temperature Range Device MC33293AT –40 to +150 –40 to +150 C MC33293ATV This document contains information on a new product. Specifications and information herein MOTOROLA ANALOG IC DEVICE DATA are subject to change without notice. QUAD LOW SIDE SWITCH (R DS(on 125 C 14 ...
Page 2
Input 1 4 Input 2 13 Input 3 12 Input 4 5 Input 1 & Single/Dual Select 11 Input 3 & Fault MAXIMUM RATINGS Rating V CC Steady-State Transient Conditions Input Pin Voltage ESD Capability ...
Page 3
STATIC ELECTRICAL CHARACTERISTICS noted. Typical values are unless otherwise noted.) Characteristic INPUT Turn ON Threshold Operating Voltage Range Quiescent Power Supply Current (All Inputs off) Overvoltage Shutdown Range Overvoltage Reset Hysteresis Input Voltage High ( ...
Page 4
STATIC ELECTRICAL CHARACTERISTICS (continued) noted. Typical values are unless otherwise noted.) Characteristic FAULT STATUS OUTPUTT Fault Status Pin Low Voltage (V PWR = 14 stl = 1.0 mA, open-load on Output ...
Page 5
Figure 1. Fuel Injector Application Block Diagram MC68HC11A1 Input Input Input Input Input 1 & Select Input ...
Page 6
Figure 2. Switching Speed Test Circuit and Response Times 10V Input Input 0V 100 s 2% Duty Cycle Gnd 5.0V 3. on(dly 13V 90 10 MC33293A Test Circuit ...
Page 7
Figure 3. Fault Status Operation with an Output-On, Open-Load Fault 5.0V 3. 5.0V V Status 0V t os(on) * Open Load Fault Reported the open occurs after the output has been on, ...
Page 8
Figure 5. Fault Status Operation with Turn On into an Over-Current Load 5.0V 3. 5.0V V Fault Status Output Shutdown 0A Over-Current condition at Turn On NOTE: Rise and fall times are ...
Page 9
Figure 7. Turn On Threshold Voltage versus Temperature 6.0 V PWR = V on(th 14 5.0 V 4.0 3.0 2.0 1.0 0 – 55 – ...
Page 10
Pin Function 1 Output 2 This is one of four open drain power MOSFET output connections. The load is connected from this pin to the positive voltage supply. 2 Output 1 This is one of four open drain power MOSFET ...
Page 11
When the Single/Dual Select pin is held at a logic high state, Control Inputs and 4 are turned OFF and can not exercise any control over the outputs. In this mode, input control transfers from a single ...
Page 12
Output-On open-load Fault The MC33293A always checks for an open-load on the outputs whether the outputs are ON or OFF. An output-on open-load Fault is detected if an open-load exists when the output is ON (corresponding input at a logic ...
Page 13
The purpose for the t os(off) delay is to prevent false fault reporting experienced with capacitance type loads. The load capacitance causes the rise in output voltage to lag even after the load has been turned OFF. The normal voltage ...
Page 14
The factors that determine the value of load resistance that will cause the onset of current limit are: I DS(limit load , and R DS(on shown below. R load(limit load / I DS(limit) ] ...
Page 15
Conditions of Outputs Non-Faulted Operation open-load Fault On Output 1 Over-Current Fault On Output 1 *NOTE: All inputs must be a logic low state for an Output-Off open-load Fault to be reported. Motorola reserves the right to make changes without ...
Page 16
Q –L– B –P– PIN 1 PIN 15X 0.010 (0.254 –Q– U –P– PIN 15 PIN 15X Q 0.010 (0.254) M ...