s71pl129ja0 Meet Spansion Inc., s71pl129ja0 Datasheet - Page 55

• Manufacturer Part Number: s71pl129ja0
• Description: Stacked Multi-chip Product Mcp Flash Memory And Psram 128 Megabit 8m X 16-bit Cmos 3.0 Volt-only Simultaneous Operation, Page Mode Flash Memory With 64/32/16 Megabit 4m/2m/1m X 16-bit Pseudo-static Ram
• Manufacturer: Meet Spansion Inc.

Command (Not es)
Reset
Secured Silicon Sector Entry
Secured Silicon Sector Exit
Secured Silicon Protection Bit Program
(Notes 5, 6)
Secured Silicon Protection Bit Status
P assword Program (Notes 5, 7, 8)
Password Verify (Notes 6, 8, 9)
Password Unlock (Notes 7, 10, 11)
PPB Program (Notes 5, 6, 12)
PPB Status
All PPB Erase (Notes 5, 6, 13, 14)
PPB Lock Bit Set
PPB Lock Bit Status
DYB Write
DYB Erase
DYB Status
PPMLB Program (Notes 5, 6, 12)
PPMLB Status
SPMLB Program (Notes 5, 6, 12)
SPMLB Status
4. During unlock and command cycles, when lower address bits are 555 or 2AAh as shown in table, address bits higher than
5. No unlock or command cycles required when bank is reading array data.
6. The Reset command is required to return to reading array (or to erase-suspend-read mode if previously in Erase Suspend)
7. Fourth cycle of autoselect command sequence is a read cycle. System must provide bank address to obtain manufacturer ID
8. The data is DQ6=1 for factory and customer locked and DQ7=1 for factory locked.
9. The data is 00h for an unprotected sector group and 01h for a protected sector group.
10. Device ID must be read across cycles 4, 5, and 6. PL129J (X0Eh = 2221h, X0Fh = 2200h).
11. System may read and program in non-erasing sectors, or enter autoselect mode, when in Program/Erase Suspend mode.
12. Program/Erase Resume command is valid only during Erase Suspend mode, and requires bank address.
13. Command is valid when device is ready to read array data or when device is in autoselect mode.
14. WP#/ACC must be at V
15. Unlock Bypass Entry command is required prior to any Unlock Bypass operation. Unlock Bypass Reset command is required
Legend:
DYB = Dynamic Protection Bit
OW = Address (A7:A0) is (00011010)
PD[3:0] = Password Data (1 of 4 portions)
PPB = Persistent Protection Bit
June 4, 2004 S29PL129J_MCP_00_A0
A11 (except where BA is required) and data bits higher than DQ7 are don’t cares.
when bank is in autoselect mode, or if DQ5 goes high (while bank is providing status information).
or device ID information. See
Program/Erase Suspend command is valid only during a sector erase operation, and requires bank address.
to return to the reading array.
(Note
(Note
(Note
(Note
(Note
7)
7)
6)
(Note
5)
5)
15)
ID
during the entire operation of command.
A d v a n c e
“Autoselect Command Sequence”
Table 13. Sector Protection Command Definitions
1
3
4
6
5
4
4
7
6
4
6
3
4
4
4
4
6
5
6
5
Addr Data Addr Data Addr Data Addr Dat a Addr Data Addr Data Addr Data
XXX
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
F0
I n f o r m a t i o n
S29PL129J for MCP
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
on page 46 for more information.
Bus Cycles (Notes 1-4)
88
90
60
60
38
C8
28
60
90
60
78
58
48
48
58
60
60
60
60
[0-3]
[0-3]
PWA
PWA
(SA)
(SA)
OW
OW
[0]
WP
WP
WP
XX
XX
SA
SA
SA
SA
PL
PL
SL
SL
[0-3]
[0-3]
PWD
PWD
[0]
(0)
(1)
(0)
RD
RD
RD
00
68
48
PD
68
60
X1
X0
68
48
68
48
PWA
(SA)
(SA)
OW
OW
WP
[1]
PL
PL
SL
SL
PWD
(0)
[1]
(0)
(0)
RD
RD
RD
48
48
40
48
48
PWA
(SA)
(SA)
OW
WP
WP
[2]
SL
PL
PWD
RD
(0)
[2]
RD
(0)
RD
(0)
RD
(0)
RD
(0)
PWA
[3]
PWD
[3]
55