TLE6216C INFINEON [Infineon Technologies AG], TLE6216C Datasheet
TLE6216C
Related parts for TLE6216C
TLE6216C Summary of contents
Page 1
Smart Quad Channel Low-Side Switch Features · Low ON-resistance 0.35 W (typ.) · Power - Package with integrated cooling area · Overload shutdown · Selective thermal shutdown · Status monitoring ...
Page 2
Pin Configuration (Top view DSO - Pin Description Pin Symbol 1 GND 2 OUT1 3 ST1 4 IN4 STBY 7 IN3 8 ST2 9 OUT2 10 GND 11 GND 12 OUT3 13 ...
Page 3
VS STBY Overtemperature ENA IN1 ST1 IN4 ST4 Overtemperature IN2 ST2 IN3 ST3 V7.1 Detailed Block Diagram internal supply Overtemperature Channel 4 Channel 1 Open Load Overload LOGIC Open Load Overload LOGIC Overtemperature Channel 3 Channel 2 Open Load Overload ...
Page 4
Block Diagram of Open Load Detection V7.1 Datasheet TLE 6216 Page 18.10.02 ...
Page 5
Maximum Ratings for T Parameter Supply voltage Supply voltage operational range Continuous drain source voltage (OUT1...OUT4) Input voltage IN1 to IN4, ENA Input voltage STBY Status output voltage Operating temperature range during clamping min during clamping; St ...
Page 6
Electrical Characteristics Parameter and Conditions ° 150 ° (unless otherwise specified) 1. Power Supply ( Supply current (Outputs ON) Supply current (Outputs OFF) ...
Page 7
Electrical Characteristics Parameter and Conditions – 40 ° 150 ° (unless otherwise specified) 5. Standby Input (STBY) Input low voltage Input high voltage Input current 6. Diagnostic ...
Page 8
Application Description This IC is especially designed to drive inductive loads (relays, electromagnetic valves). Integrated clamp-diodes limit the output voltage when inductive loads are discharged. Four open-drain logic outputs indicate the status of the integrated circuit. The following conditions are ...
Page 9
In the off mode, the output voltage is monitored. An open load condition is detected when the output voltage of a given channel is below the supply voltage V . Also the output voltages of two outputs ...
Page 10
The following diagrams show the dynamical behavior of the status output in case of different errors. The symbol F defines the moment of failure occurrence. Output open load or short circuit to GND IN ST Output overload IN ST Overtemperature ...
Page 11
Test Circuit V7.1 Datasheet TLE 6216 TLE 6216 Page 18.10.02 ...
Page 12
Application Circuit The blocking capacitor C is recommended to avoid critical negative voltage spikes case of battery interruption during OFF-commutation. V7.1 TLE 6216 Status Control Enable Outputs Inputs Input Page Datasheet TLE 6216 18.10.02 ...
Page 13
Output Slope INL 85 15% t fall Overload Switch OFF Delay D(lim) I D(OL V7.1 Timing Diagrams t off ...
Page 14
Ordering code Type TLE6216 G TLE6216 C Pad Assignment Out4 IN1 ST4 TLE 6216 ST1 IN4 Out1 V7.1 Ordering Code on request on request ST3 IN2 ENA GND Stby ST2 VS IN3 Out2 Page Datasheet TLE 6216 ...
Page 15
Package dimensions All dimensions V7 13.7 -0 1.27 = 11.43 1. ...
Page 16
Revision List: 01.09.2001 Target Datasheet 01.11.2001 First revision 04.03.2002 Second revision 30.04.2002 Third revision 30.07.2002 Preliminary Datasheet 09.09.2002 Final Datasheet 18.10.02 Update typers V7.1 Datasheet TLE 6216 V7.1 Page 18.10.02 ...
Page 17
Published by Infineon Technologies AG, Bereich Kommunikation St.-Martin-Strasse 76, D-81541 München © Infineon Technologies AG 1999 All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of ...