V23814-U1306-M130 INFINEON [Infineon Technologies AG], V23814-U1306-M130 Datasheet - Page 7

• Manufacturer Part Number: V23814-U1306-M130
• Description: Parallel Optical Link: PAROLI T X AC, 1.6 Gbit/s
• Manufacturer: INFINEON [Infineon Technologies AG]

Fiber Optics
Pin#
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
Pin Name
V
V
t.b.l.o.
DO04P
DO04N
V
DO05P
DO05N
V
V
DO06P
DO06N
V
V
DO07P
DO07N
V
V
DO08P
DO08N
V
V
V
DO09P
DO09N
t.b.l.o.
V
V
DO10P
DO10N
V
V
DO11P
DO11N
V
V
DO12P
DO12N
V
V
V
t.b.l.o.
V
V
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
CC3
Level/Logic Description
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
LVDS Out
Ground
Ground
to be left open
Data Output #4, non-inverted
Data Output #4, inverted
Ground
Data Output #5, non-inverted
Data Output #5, inverted
Ground
Ground
Data Output #6, non-inverted
Data Output #6, inverted
Ground
Ground
Data Output #7, non-inverted
Data Output #7, inverted
Ground
Ground
Data Output #8, non-inverted
Data Output #8, inverted
Ground
Ground
Ground
Data Output #9, non-inverted
Data Output #9, inverted
to be left open
Ground
Ground
Data Output #10, non-inverted
Data Output #10, inverted
Ground
Ground
Data Output #11, non-inverted
Data Output #11, inverted
Ground
Ground
Data Output #12, non-inverted
Data Output #12, inverted
Ground
Ground
Ground
to be left open
Ground
Power supply voltage of digital
circuitry
7
Optical Port
Designed for Infineon Simplex MT Connector (SMC)
• Port outside dimensions: 15.4 mm x 6.8 mm (width x height)
• MT compatible fiber spacing (250 m) and alignment pin
• Alignment pins fixed in module port
• Integrated mechanical keying
• process plug (SMC dimensions) included with every module
• cleaning of port and connector interfaces necessary prior
Features of Infineon Simplex MT Connector (SMC)
(as part of optional PAROLI fiber optic cables)
• Uses standardized MT ferrule
• MT compatible fiber spacing (250 m) and alignment pin
• Snap-in mechanism
• Ferrule bearing spring loaded
• Not strain-relieved
• Integrated mechanical keying
Cleaning and Soldering Process for
Transmitter and Receiver
Special care must be taken to remove residuals from the sol-
dering and washing process, which can impact the mechanical
function. Avoid the use of aggressive organic solvents like
ketones, ethers, etc. Consult the supplier of the PAROLI mod-
ules and the supplier of the solder paste and flux for recom-
mended cleaning solvents.
The following common cleaning solvents will not affect the
module: deionized water, ethanol, and isopropyl alcohol. Air-
drying is recommended to a maximum temperature of 100°C.
Do not use ultrasonics.
During soldering, heat must be applied to the leads only, to
ensure that the case temperature never exceeds 100°C. The
module must be mounted with a hot-bar soldering process
using a SnPb solder type, e.g.. S-Sn63Pb37E, in accordance
with ISO 9435.
Pin#
67
68
69
70
71
72
spacing (4600 m)
to mating
spacing (4600 m)
V23814/15-U1306-M130 Parallel Optical Link: PAROLI
Pin Name
-SD12
ENSD
t.b.l.o.
V
V
V
CC2
CC1
EE
Level/Logic Description
LVCMOS
Out
low active
LVCMOS In High=SD1 and SD12 function
Signal Detect on fiber #12
Low=signal of sufficient AC
power is present on fiber #12
High=signal on fiber #12 is
insufficient
enabled
Low=SD1 and SD12 are set to
permanent active.Internal pull-
up pulls to high level when in-
put is left open.
to be left open
Power supply voltage of LVDS
outputs
Power supply voltage of ampli-
fier
Ground
Tx/Rx AC, 1.6 Gbit/s