BTS5210G_09 INFINEON [Infineon Technologies AG], BTS5210G_09 Datasheet
BTS5210G_09
Related parts for BTS5210G_09
BTS5210G_09 Summary of contents
Page 1
...
Page 2
Product Summary • • • • • • • • • • • • • • • • • • • • • • • • • AEC Qualified • Green product (RoHS compliant) Data Sheet Smart High-Side Power Switch ...
Page 3
Data Sheet control and protection circuit equivalent to channel 1 3 Smart High-Side Power Switch BTS5210G Rev. 1.3, 2009-04-16 ...
Page 4
Pin Definitions and Functions Pin Symbol Function Positive power supply voltage. Design the 1,7, wiring for the simultaneous max. short circuit V bb 8,14 currents from channel and also for low thermal resistance 2 GND Logic Ground ...
Page 5
Parameter Supply voltage (overvoltage protection see page 6) Supply voltage for full short circuit protection T = -40 ...+150°C j,start Load current (Short-circuit current, see page 6) ) Load dump protection 1 V LoadDump = 2 Ω ...
Page 6
Parameter and Conditions Thermal resistance junction - soldering point 6)7) junction – ambient cooling area Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching ...
Page 7
Parameter and Conditions, = -40...+150° unless otherwise specified j bb Operating Parameters Operating voltage ) Undervoltage switch off 10 ) Overvoltage protection Standby current ...
Page 8
Parameter and Conditions -40...+150° unless otherwise specified j bb Reverse Battery ) 17 Reverse battery voltage Drain-source diode voltage = - 2 +150° Diagnostic Characteristics Open load ...
Page 9
Truth Table ( each channel ) Normal operation Open load Overtemperature L = "Low" Level X = don't care H = "High" Level Status signal valid after the time delay shown in the timing diagrams Parallel switching of channel 1 ...
Page 10
Input circuit (ESD protection), The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Status output, ST1 or ST2 ESD-Zener diode: 6.1 V typ., max 0.3 mA 1.6 mA. The use of ESD ...
Page 11
GND disconnect with GND pull up Any kind of load > GND IN IN(T+) Due to V > low signal available. GND ST V disconnect with energized inductive bb load For ...
Page 12
Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2 = low EE RII ...
Page 13
Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 to channel 4 Figure 1a: V turn on: bb Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure ...
Page 14
Figure 3b: Turn on into short circuit: shut down by overtemperature, restart by cooling (two parallel switched channels 1 and 2) ST1 and ST2 have to be configured as a 'Wired OR' function ST1/2 with a single pull-up resistor. Figure ...
Page 15
Package Outlines Figure 1 PG-DSO-14-37 (Plastic Dual Small Outline Package) (RoHS-compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant ...
Page 16
Revision History Version Date Changes Rev. 1.3 2009-04-16 Modification of the package name extension. V1.2 2007-09-25 Modification of the package drawing. V1.1 2007-05-29 Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding ...
Page 17
Edition 2009-04-16 Published by Infineon Technologies AG 81726 Munich, Germany 2009 Infineon Technologies AG © All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With ...