AM79C978 Advanced Micro Devices, AM79C978 Datasheet - Page 157

• Manufacturer Part Number: AM79C978
• Description: Single-Chip 1/10 Mbps PCI Home Networking Controller
• Manufacturer: Advanced Micro Devices

10
9
8
RES
MEMCMD
EXTREQ
The NOUFLO bit has no effect
when the Am79C978 controller is
operating in the NO-SRAM mode.
Reserved location. Written as
zero and read as undefined.
Memory Command used for burst
read accesses to the transmit
buffer. When MEMCMD is set to
0, all burst read accesses to the
transmit buffer are of the PCI
command type Memory Read
Line (type 14). When MEMCMD
is set to 1, all burst read accesses
to the transmit buffer are of the
PCI command type Memory
Read Multiple (type 12).
Extended Request. This bit con-
trols the deassertion of REQ for a
burst transaction. If EXTREQ is
set to 0, REQ is deasserted at the
beginning of a burst transaction.
(The Am79C978 controller never
performs more than one burst
transaction within a single bus
mastership period.) In this mode,
the Am79C978 controller relies
on the PCI latency timer to get
enough bus bandwidth, in case
Setting the NOUFLO bit guaran-
tees that the Am79C978 control-
ler will never suffer transmit
underflows, because the arbiter
that controls transfers to and from
the SRAM guarantees a worst
case latency on transfers to and
from the MAC and Bus Transmit
FIFOs such that it will never un-
derflow if the complete packet
has
Am79C978
packet transmission begins.
Read/Write accessible only when
either the STOP or the SPND bit
is set. NOUFLO is cleared to 0 af-
ter H_RESET or S_RESET and
is unaffected by STOP.
This bit is read accessible al-
ways; write accessible only when
either the STOP or the SPND bit
is set. MEMCMD is cleared by
H_RESET and is not affected by
S_RESET or STOP.
been
DMA’d
controller
into
before
the
Am79C978
7
DWIO
the system arbiter also removes
GNT at the beginning of the burst
transaction. If EXTREQ is set to
1, REQ stays asserted until the
last but one data phase of the
burst transaction is done. This
mode is useful for systems that
implement an arbitration scheme
without preemption and require
that REQ stays asserted through-
out the transaction.
EXTREQ should not be set to 1
when the Am79C978 controller is
used in a PCI bus application.
This bit is read accessible al-
ways, write accessible only when
either the STOP or the SPND bit
is set. EXTREQ is cleared by
H_RESET and is not affected by
S_RESET or STOP.
Double Word I/O. When set, this
bit indicates that the Am79C978
controller is programmed for
DWord I/O (DWIO) mode. When
cleared, this bit indicates that the
Am79C978 controller is pro-
grammed for Word I/O (WIO)
mode. This bit affects the I/O Re-
source Offset map and it affects
the
Am79C978 controller’s I/O re-
sources. See the DWIO and WIO
sections for more details.
The initial value of the DWIO bit is
determined by the programming
of the EEPROM.
The value of DWIO can be al-
tered
Am79C978 controller. Specifical-
ly, the Am79C978 controller will
set DWIO if it detects a DWord
write access to offset 10h from
the Am79C978 controller’s I/O
base address (corresponding to
the RDP resource).
Once the DWIO bit has been set
to a 1, only a H_RESET or an EE-
PROM read can reset it to a 0.
(Note that the EEPROM read op-
eration will only set DWIO to a 0 if
the appropriate bit inside of the
EEPROM is set to 0.)
defined
automatically
width
by
of
157
the
the