73K212AL TDK [TDK Electronics], 73K212AL Datasheet
73K212AL
Related parts for 73K212AL
73K212AL Summary of contents
Page 1
DESCRIPTION The 73K222BL is a highly integrated single-chip modem IC which provides the functions needed to construct a CCITT V.22, V.21, Bell 212A and Bell 103, compatible modem, capable of 1200 bit/s full- duplex operation over dial-up lines. The 73K222BL ...
Page 2
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid DESCRIPTION (continued) The 73K222BL is designed to appear to the systems designer as a microprocessor peripheral, and will easily interface with microprocessors (80C51 typical) for control of modem functions ...
Page 3
Serial data from the demodulator is passed first through the data descrambler and then through the SYNC/ASYNC converter. The converter will re-insert any deleted stop bits and transmit output data at an intra-character rate (bit-to- bit timing greater ...
Page 4
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid FUNCTIONAL DESCRIPTION PARALLEL BUS INTERFACE Four 8-bit registers are provided for control, option select and status monitoring. These registers are addressed with the AD0, AD1, and AD2 multiplexed address ...
Page 5
PIN DESCRIPTION POWER NAME PIN TYPE GND 1 VDD 16 VREF 31 ISET 28 PARALLEL CONTROL INTERFACE ALE 13 AD0-AD7 5-12 I/O Tristate CS 23 CLK 2 O INT RESET 30 I/with Pulldown V.22, V.21, Bell 212A, ...
Page 6
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid PARALLEL CONTROL INTERFACE NAME PIN TYPE WR 14 SERIAL CONTROL INTERFACE NAME PIN TYPE AD0-AD2 5-7 DATA (AD7 NOTE: The serial control mode ...
Page 7
DTE USER NAME PIN TYPE EXCLK 22 RXCLK 26 RXD 25 O/ Weak Pull-up TXCLK 21 TXD 24 ANALOG INTERFACE AND OSCILLATOR NAME PIN TYPE RXA 32 TXA1 18 TXA2 17 XTL1 3 XTL2 V.22, V.21, Bell ...
Page 8
... RXD PIN 0 = NORMAL 1 = WEAK PULL- 110 1 REGISTER 00XX = 73K212AL, 322L, 321L X = Undefined, mask in software 01XX = 73K221AL, 302L 10XX = 73K222AL, 222BL 1100 = 73K224L, 224BL 1110 = 73K324L, 324BL NOTE: When a register containing reserved control bits is written into, the reserved bits must be programmed as 0's. ...
Page 9
CONTROL REGISTER CR0 MODUL. 0 TRANSMIT 000 OPTION MODE 3 BIT NO. NAME D0 Answer/ Originate D1 Transmit Enable D5, D4, D3, D2 Transmit Mode D6 V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid ...
Page 10
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid CONTROL REGISTER 0 (continued CR0 MODUL. 0 TRANSMIT 000 OPTION BIT NO. NAME D7 Modulation Option CONTROL REGISTER CR1 TRANSMIT TRANSMIT 001 PATTERN PATTERN ...
Page 11
CONTROL REGISTER 1 (continued CR1 TRANSMIT TRANSMIT 001 PATTERN PATTERN 1 0 BIT NO. NAME D4 Bypass Scrambler D5 Enable Detect D7, D6 Transmit Pattern DETECT REGISTER RECEIVE 010 BIT NO. NAME D0 ...
Page 12
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid DETECT REGISTER (continued RECEIVE 010 BIT NO. NAME D2 Answer Tone Detect D3 Carrier Detect D4 Unscrambled Mark Detect D5 ReceiveData D6, D7 Not ...
Page 13
TONE REGISTER (continued RXD TRANSMIT 011 OUTPUT GUARD CONTR. TONE BIT NO. NAME D3, D2, DTMF D1 Transmit DTMF D5 Transmit Answer Tone V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem ...
Page 14
... RXD. 1 Disables RXD pin. The RXD pin reverts to a high impedance with internal weak pull-up resistor CONDITION DESCRIPTION Indicates device type 73K212AL, 73K321L or 73K322L 73K221AL or 73K302L 73K222AL, 73K222BL 73K224AL ...
Page 15
ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS PARAMETER VDD Supply Voltage Storage Temperature Reflow Soldering Temperature (10 sec.)/VPS (10 sec.) Applied Voltage NOTE: All inputs and outputs are protected from static charge using built-in, industry standard protection devices and all outputs are ...
Page 16
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid DC ELECTRICAL CHARACTERISTICS (TA = -40° 85° C, VDD = recommended range unless otherwise noted.) PARAMETER IDD, SUPPLY CURRENT IDDA, Active IDD1, Power-down IDD2, Power-down DIGITAL INPUTS ...
Page 17
ELECTRICAL SPECIFICATIONS DYNAMIC CHARACTERISTICS AND TIMING (TA = -40°C to +85°C, VDD = recommended range unless otherwise noted.) PARAMETER DPSK MODULATOR Carrier Suppression Output Amplitude FSK MODULATOR/DEMODULATOR Output Frequency Error Transmit Level Harmonic Distortion in 700-2900 Hz band Output Bias ...
Page 18
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid DYNAMIC CHARACTERISTICS AND TIMING PARAMETER CARRIER DETECT Threshold Delay Time Hysteresis Hold Time ANSWER TONE DETECTOR Detect Level Delay Time Hold Time Detect Frequency Range OUTPUT SMOOTHING FILTER Output ...
Page 19
DYNAMIC CHARACTERISTICS AND TIMING PARAMETER GUARD TONE GENERATOR Tone Accuracy Tone Level (Below DPSK Output) Harmonic Distortion 700 to 2900 Hz TIMING (Refer to Timing Diagrams) TAL TLA ADD TLC TCL TRD TLL TRDF TRW TWW TDW TWD TCKD TCKW ...
Page 20
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid TIMING DIAGRAMS TLL ALE RD WR TAL ADDRESS AD0-AD7 CS EXCLK RD TAC TCA ADDRESS A0-A2 TRD D0 DATA FIGURE 3: Read Timing Diagram (Serial Version) EXCLK WR A0-A2 ...
Page 21
APPLICATIONS INFORMATION GENERAL CONSIDERATIONS Figure 5 shows the basic circuit diagram for a 73K222BL modem integrated circuit designed to be used in conjunction with a control processor, a UART or RS-232 serial data interface, and a DAA phone line interface ...
Page 22
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid APPLICATIONS INFORMATION DIRECT ACCESS ARRANGEMENT (DAA) The DAA (Direct Access Arrangement) required for the 73K222BL consists of an impedance matching resistor, telecom coupling transformer, and ring detection and fault ...
Page 23
To avoid problems, power supply and ground traces should be routed separately to the analog and digital functions on the board, and digital signals should not be routed near low level or high impedance analog traces. The analog and digital ...
Page 24
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid APPLICATIONS INFORMATION * 73K222BL BER vs SIGNALTO NOISE 10 -2 HIGH BAND RECEIVE DPSK OPERATION -3 10 600 BPS 3002 FLAT - ...
Page 25
MECHANICAL SPECIFICATIONS 32-Pin PLCC 0.453 (11.51) 0.449 (11.40) PIN NO. 1 IDENT. 0.595 (15.11) 0.585 (14.86) 0.495 (12.57) 0.485 (12.32) 44-Lead TQFP 0.09 (0.035) 1.35 (0.053) 0.20 (0.008) 1.45 (0.057) V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated ...
Page 26
V.22, V.21, Bell 212A, Bell 103 Single-Chip Modem with Integrated Hybrid PACKAGE PIN DESIGNATIONS (Top View AD0 5 AD1 6 AD2 7 AD3 8 AD4 9 AD5 10 AD6 11 DATA/AD7 12 ALE ...