SPC5646CCF0MLU1 Freescale Semiconductor, SPC5646CCF0MLU1 Datasheet - Page 38

• Manufacturer Part Number: SPC5646CCF0MLU1
• Description: 32-bit Microcontrollers - MCU 3M FLASH,25 6K RAM,CSE
• Manufacturer: Freescale Semiconductor

Specifications of SPC5646CCF0MLU1

• Rohs: yes
• Core: e200
• Processor Series: MPC5646C
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 120 MHz
• Program Memory Size: 3 MB
• Data Ram Size: 256 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 0.3 V to 6.2 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-176
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit, 12 bit
• A/d Channels Available: 33
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 147
• Number Of Timers: 32
• Program Memory Type: Flash
• Supply Voltage - Max: 6.2 V
• Supply Voltage - Min: 0.3 V

Electrical Characteristics
4
This section contains electrical characteristics of the device as well as temperature and power considerations.
This product contains devices to protect the inputs against damage due to high static voltages. However, it is advisable to take
precautions to avoid application of any voltage higher than the specified maximum rated voltages.
To enhance reliability, unused inputs can be driven to an appropriate logic voltage level (V
by the internal pull-up and pull-down, which is provided by the product for most general purpose pins.
The parameters listed in the following tables represent the characteristics of the device and its demands on the system.
In the tables where the device logic provides signals with their respective timing characteristics, the symbol “CC” for Controller
Characteristics is included in the Symbol column.
In the tables where the external system must provide signals with their respective timing characteristics to the device, the symbol
“SR” for System Requirement is included in the Symbol column.
4.1
The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better
understanding, the classifications listed in
appropriate.
4.2
Portions of the device configuration, such as high voltage supply is controlled via bit values in the Non-Volatile User Options
Register (NVUSRO). For a detailed description of the NVUSRO register, see MPC5646C Reference Manual.
38
7
8
Classification tag
When MBIST is enabled to run ( STCU Enable = 1), the application must not drive or tie PAD[178) (MDO[0]) to 0 V
before the device exits reset (external reset is removed) as the pad is internally driven to 1 to indicate MBIST
operation. When MBIST is not enabled (STCU Enable = 0), there are no restriction as the device does not internally
drive the pad.
These pins can be configured as Nexus pins during reset by the debugger writing to the Nexus Development
Interface "Port Control Register" rather than the SIUL. Specifically, the debugger can enable the MDO[7:0], MSEO,
and MCKO ports by programming NDI (PCR[MCKO_EN] or PCR[PSTAT_EN]). MDO[8:11] ports can be enabled
by programming NDI ((PCR[MCKO_EN] and PCR[FPM]) or PCR[PSTAT_EN]).
Electrical Characteristics
Parameter classification
NVUSRO register
P
C
T
D
The classification is shown in the column labeled “C” in the parameter tables where
appropriate.
Those parameters are guaranteed during production testing on each individual device.
Those parameters are achieved by the design characterization by measuring a statistically
relevant sample size across process variations.
Those parameters are achieved by design characterization on a small sample size from typical
devices under typical conditions unless otherwise noted. All values shown in the typical column
are within this category.
Those parameters are derived mainly from simulations.
MPC5646C Microcontroller DataSheet, Rev. 5.1
Table 5
Table 5. Parameter classifications
are used and the parameters are tagged accordingly in the tables where
NOTE
Tag description
DD
or V
SS_HV
). This could be done
Freescale