SST89E554RC-40-C-PI Microchip Technology, SST89E554RC-40-C-PI Datasheet - Page 52

• Manufacturer Part Number: SST89E554RC-40-C-PI
• Description: 8-bit Microcontrollers - MCU 32KB+8KB 40ns
• Manufacturer: Microchip Technology

Specifications of SST89E554RC-40-C-PI

• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 1 KB
• On-chip Adc: No
• Operating Supply Voltage: 4.5 V to 5.5 V
• Package / Case: PDIP-40
• Mounting Style: Through Hole
• Data Rom Size: 128 B
• Interface Type: SPI, UART
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• On-chip Dac: No
• Processor Series: FlashFlex
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 4.5 V

EOL Data Sheet
8.3 Compare/Capture Modules
Each PCA module has an associated SFR with it. These
registers are: CCAPM0 for module 0, CCAPM1 for module
1, etc. Refer to “PCA Compare/Capture Module Mode Reg-
ister (CCAPMn)” on page 29 for details. The registers each
contain 7 bits which are used to control the mode each
module will operate in. The ECCF bit (CCAPMn.0 where n
= 0, 1, 2, 3, or 4 depending on module) will enable the CCF
flag in the CCON SFR to generate an interrupt when a
match or compare occurs. PWM (CCAPMn.1) enables the
pulse width modulation mode. The TOG bit (CCAPMn.2)
when set, causes the CEX output associated with the mod-
ule to toggle when there is a match between the PCA
counter and the module’s capture/compare register. When
there is a match between the PCA counter and the mod-
ule’s capture/compare register, the MATn (CCAPMn.3) and
the CCFn bit in the CCON register to be set.
TABLE
©2007 Silicon Storage Technology, Inc.
Symbol
CCAP0H PCA Module 0
CCAP0L
CCAP1H PCA Module 1
CCAP1L
CCAP2H PCA Module 2
CCAP2L
CCAP3H PCA Module 3
CCAP3L
CCAP4H PCA Module 4
CCAP4L
8-4: PCA H
Description
Compare/Capture
Registers
Compare/Capture
Registers
Compare/Capture
Registers
Compare/Capture
Registers
Compare/Capture
Registers
IGH AND
Address
Direct
EAH
EBH
FCH
ECH
FDH
EDH
EEH
FAH
FBH
FEH
L
OW
R
EGISTER
MSB
Bit Address, Symbol, or Alternative Port Function
C
OMPARE
52
/C
APTURE
Bits CAPN (CCAPMn.4) and CAPP (CCAPMn.5) deter-
mine whether the capture input will be active on a positive
edge or negative edge. The CAPN bit enables the negative
edge that a capture input will be active on, and the CAPP
bit enables the positive edge. When both bits are set, both
edges will be enabled and a capture will occur for either
transition. The last bit in the register ECOM (CCAPMn.6)
when set, enables the comparator function. Table 8-5
shows the CCAPMn settings for the various PCA functions.
There are two additional register associated with each of
the PCA modules: CCAPnH and CCAPnL. They are regis-
ters that hold the 16-bit count value when a capture occurs
or a compare occurs. When a module is used in PWM
mode, these registers are used to control the duty cycle of
the output. See Figure 8-1.
CCAP0H[7:0]
CCAP1H[7:0]
CCAP2H[7:0]
CCAP3H[7:0]
CCAP4H[7:0]
CCAP0L[7:0]
CCAP1L[7:0]
CCAP2L[7:0]
CCAP3L[7:0]
CCAP4L[7:0]
M
ODULES
SST89E564RD / SST89V564RD
SST89E554RC / SST89V554RC
FlashFlex MCU
LSB
S71207-08-EOL
RESET
Value
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
T8-4.0 1207
1/07