MC68HC908QT1VDW Freescale Semiconductor, MC68HC908QT1VDW Datasheet - Page 141

• Manufacturer Part Number: MC68HC908QT1VDW
• Description: 8-bit Microcontrollers - MCU 8 Bit 8MHz
• Manufacturer: Freescale Semiconductor

Specifications of MC68HC908QT1VDW

• Product Category: 8-bit Microcontrollers - MCU
• Core: HC08
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 8 MHz
• Program Memory Size: 1.5 KB
• Data Ram Size: 128 B
• On-chip Adc: No
• Operating Supply Voltage: 3.3 V to 5.5 V
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: SOIC-8
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Program Memory Type: Flash
• Factory Pack Quantity: 96
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 2.7 V

Simple monitor commands can access any memory address. In monitor mode, the MCU can execute
code downloaded into RAM by a host computer while most MCU pins retain normal operating mode
functions. All communication between the host computer and the MCU is through the PTA0 pin. A
level-shifting and multiplexing interface is required between PTA0 and the host computer. PTA0 is used
in a wired-OR configuration and requires a pullup resistor.
The monitor code has been updated from previous versions of the monitor code to allow enabling the
internal oscillator to generate the internal clock. This addition, which is enabled when IRQ is held low out
of reset, is intended to support serial communication/programming at 9600 baud in monitor mode by using
the internal oscillator, and the internal oscillator user trim value OSCTRIM (FLASH location $FFC0, if
programmed) to generate the desired internal frequency (3.2 MHz). Since this feature is enabled only
when IRQ is held low out of reset, it cannot be used when the reset vector is programmed (i.e., the value
is not $FFFF) because entry into monitor mode in this case requires V
remain low during this monitor session in order to maintain communication.
Table 15-1
may be entered after a power-on reset (POR) and will allow communication at 9600 baud provided one
of the following sets of conditions is met:
Freescale Semiconductor
•
•
•
2
3
5
1 μF
1 μF
DB9
If $FFFE and $FFFF do not contain $FF (programmed state):
–
–
If $FFFE and $FFFF contain $FF (erased state):
–
–
If $FFFE and $FFFF contain $FF (erased state):
–
The external clock is 9.8304 MHz
IRQ = V
The external clock is 9.8304 MHz
IRQ = V
IRQ = V
+
+
shows the pin conditions for entering monitor mode. As specified in the table, monitor mode
1
3
4
5
7
8
C1+
C1–
C2+
C2–
Figure 15-12. Monitor Mode Circuit (Internal Clock, No High Voltage)
TST
DD
SS
MAX232
(internal oscillator is selected, no external clock required)
(this can be implemented through the internal IRQ pullup)
V+
V–
16
15
2
10
6
1 μF
9
MC68HC908QY/QT Family Data Sheet, Rev. 6
V
DD
+
+
1 μF
2
74HC125
1
+
3
1 μF
74HC125
6
4
10 kΩ
5
V
DD
10 kΩ
*
* Value not critical
N.C.
N.C.
RST (PTA3)
OSC1 (PTA5)
IRQ (PTA2)
PTA0
TST
on IRQ. The IRQ pin must
Monitor Module (MON)
PTA1
PTA4
V
V
DD
SS
V
N.C.
N.C.
DD
0.1 μF
141