MAX1276EVKIT Maxim Integrated, MAX1276EVKIT Datasheet - Page 6

• Manufacturer Part Number: MAX1276EVKIT
• Description: Data Conversion IC Development Tools Evaluation Kit/Evaluation System for the MAX1070/71/72/75#79/MAX1224/25/MAX1274#79
• Manufacturer: Maxim Integrated
• Series: MAX1276, MAX1278r

Specifications of MAX1276EVKIT

• Interface Type: QSPI, Serial (SPI, Microwire)

• Power supplies for the MAX1276EVKIT:
Follow the steps below to verify board operation.
1) Carefully connect the boards by aligning the 40-pin
2) It is highly recommended that shunts for JU1 and
MAX1276 Evaluation Kit/Evaluation System
Table 4. Supplies for Optional Devices and Allowed Reference Jumper Settings
6
RESOLUTION (BITS)
1) +5.0V VDD supply
2) +5.0V VLOGIC supply
3) +7.0V positive supply buffer
4) -3.0V negative supply buffer
5) 4.096V
6) 2.048V DC supply for common-mode voltage
header of the MAX1276EVKIT with the 40-pin con-
nector of the 68HC16 (µC) module. Gently press
them together. The two boards should be flush
against one another.
JU2 be removed until the test device and buffers
are fully powered and input levels have been veri-
fied to avoid possible damage to the test device if
pins are taken above the VDD supply or below
ground. See the Input-Signal Setup Procedure sec-
tion for a description of the possible input options.
_______________________________________________________________________________________
10
12
P-P
AC input
JU3
1-2
2-3
1-2
1-2
2-3
1-2
or
or
REFERENCE VOLTAGE
Procedure
0 to VDD
0 to VDD
External
External
Internal
Internal
Internal
Internal
2.048
4.096
2.048
4.096
(V)
3) Set jumpers JU3–JU6 as shown in
4) Connect the 7.5V to 20V DC power source to the µC
5) Connect the power supplies for the MAX1276EVKIT
6) Connect the serial cable from the computer’s serial
7) Install the MAX1276 EV kit software on the personal
8) Start the MAX1276 program by clicking its icon in
9) The program prompts the user to connect the µC
module at the terminal block located next to the
ON/OFF switch, along the top edge of the µC mod-
ule. Observe the polarity marked on the board.
(see
port to the µC module.
computer by running the INSTALL.EXE program on
the CD-ROM disk. The program files are copied
and icons are added to the Windows start menu.
the Start menu.
module and turn on its power supply. Slide SW1 to
the ON position and turn on the power supplies for
the MAX1276EVKIT board.
V
DD
4.5 to 5.25
4.5 to 5.25
4.5 to 5.25
4.5 to 5.25
2.7 to 3.6
2.7 to 3.6
2.7 to 3.6
2.7 to 3.6
Table
SUPPLY (V)
2).
OUTPUT
CODING
Unipolar
Unipolar
Unipolar
Unipolar
Unipolar
Unipolar
Unipolar
Unipolar
Bipolar
Bipolar
Bipolar
Bipolar
Bipolar
Bipolar
Bipolar
Bipolar
Table
1.
MAX1070
MAX1071
MAX1072
MAX1075
MAX1077
MAX1079
MAX1076
MAX1078
MAX1224
MAX1225
MAX1274
MAX1275
MAX1277
MAX1279
MAX1276
MAX1278
DEVICE