M95640-WMN6P STMicroelectronics, M95640-WMN6P Datasheet - Page 18

• Manufacturer Part Number: M95640-WMN6P
• Description: IC EEPROM 64KBIT 10MHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M95640-WMN6P

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 64K (8K x 8)
• Speed: 10MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Organization: 8 K x 8
• Interface Type: SPI
• Maximum Clock Frequency: 10 MHz
• Access Time: 40 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 4 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 3.3 V, 5 V
• Memory Configuration: 8192 X 8
• Clock Frequency: 10MHz
• Supply Voltage Range: 2.5V To 5.5V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8615-5; M95640-WMN6P

Instructions
6.3
6.3.1
6.3.2
6.3.3
6.3.4
18/44
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction allows the Status Register to be read. The
Status Register may be read at any time, even while a Write or Write Status Register cycle
is in progress. When one of these cycles is in progress, it is recommended to check the
Write In Progress (WIP) bit before sending a new instruction to the device. It is also possible
to read the Status Register continuously, as shown in
The Status Register format is shown in
Register are as follows:
WIP bit
The Write In Progress (WIP) bit indicates whether the memory is busy with a Write or Write
Status Register cycle. When set to 1, such a cycle is in progress, when reset to 0 no such
cycle is in progress.
WEL bit
The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch.
When set to 1 the internal Write Enable Latch is set, when set to 0 the internal Write Enable
Latch is reset and no Write or Write Status Register instruction is accepted.
BP1, BP0 bits
The Block Protect (BP1, BP0) bits are non-volatile. They define the size of the area to be
software protected against Write instructions. These bits are written with the Write Status
Register (WRSR) instruction. When one or both of the Block Protect (BP1, BP0) bits is set to
1, the relevant memory area (as defined in
(WRITE) instructions. The Block Protect (BP1, BP0) bits can be written provided that the
Hardware Protected mode has not been set.
SRWD bit
The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write
Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware Protected mode (when the Status Register
Write Disable (SRWD) bit is set to 1, and Write Protect (W) is driven low). In this mode, the
non-volatile bits of the Status Register (SRWD, BP1, BP0) become read-only bits and the
Write Status Register (WRSR) instruction is no longer accepted for execution.
Table 4.
Status Register Write Protect
SRWD
b7
Status Register format
0
0
Doc ID 5711 Rev 12
Table 4
0
Table
and the status and control bits of the Status
4) becomes protected against Write
BP1
Block Protect bits
Figure
M95320, M95320-W, M95320-R
Write Enable Latch bit
9.
BP0
WEL
Write In Progress bit
WIP
b0