BTS716G Infineon Technologies, BTS716G Datasheet

Page 1

... Data Sheet Smart High-Side Power Switch Ω Ω Ω  Block Diagram 1 BTS716G Package P-DSO-20 PG-DSO20 V1.0, 2007-05-13 ...

Page 2

... IN4 Data Sheet control and protection circuit of channel 2 control and protection circuit of channel 3 control and protection circuit of channel 4 2 Smart High-Side Power Switch BTS716G V1.0, 2007-05-13 ...

Page 3

... ST3/4 open drain, low on failure 2 GND1/2 Ground of chip 1 (channel 1,2) 6 GND3/4 Ground of chip 2 (channel 3,4) Data Sheet Smart High-Side Power Switch Pin configuration (top view GND1/2 2 IN1 3 ST1/2 4 IN2 5 GND3/4 6 IN3 7 ST3/4 8 IN4 BTS716G • OUT1 17 OUT2 OUT3 13 OUT4 V1.0, 2007-05-13 ...

Page 4

... IN: ST require an external current limit for the GND and status pins (a 150Ω bb(AZ) 2 (one layer, 70µm thick) copper area for Smart High-Side Power Switch BTS716G Symbol Values self-limited Load dump T -40 ...

Page 5

... I one channel active: L(NOM L(GNDhigh 90 OUT 10 OUT off = 12 Ω / OUT Ω / OUT L 2 (one layer, 70µm thick) copper area for Smart High-Side Power Switch BTS716G Values min typ max -- -- Values min typ max -- 110 140 -- 210 280 -- 2.3 2 ...

Page 6

... T jt ∆ T require an external current limit for the GND and status pins (a 150Ω bb(AZ) ON(CL) 6 Smart High-Side Power Switch Values min typ max 0.5 0.9 -- 1.9 3 6 150 -- -- table of protection functions and V1.0, 2007-05-13 BTS716G Unit 11 µ 11) µ ° ...

Page 7

... IN(off IN(on +1.6 mA +1.6 mA Smart High-Side Power Switch Values min typ -- -- bb -- 600 ON 1.7 2.8 OUT(OL) 1 2.5 4 IN(T+) 1.0 -- IN(T-) -- 0.2 IN( 5.4 -- ST(high ST(low) V1.0, 2007-05-13 BTS716G Unit max 4.0 V 6.0 kΩ 2 —s 20 —s -- —s 500 —s 20 µA 20 µ 0.6 ...

Page 8

... Chip 1 IN1 IN2 Chip 2 IN3 IN4 Channel 1 ( Channel 2 ( both channel Channel 1 ( Channel 2 ( high impedance, potential depends on external circuit = 150 Ω single resistor GND1 GND2 8 Smart High-Side Power Switch OUT1 OUT2 ST1/2 OUT3 OUT4 ST3 Ω for reverse GND V1.0, 2007-05-13 BTS716G ...

Page 9

... Open-load detection, OFF-state diagnostic condition: Open Load OUT < 375 Ω ST(ON) GND disconnect Any kind of load. In case high is V Due to V > GND 9 Smart High-Side Power Switch BTS716G = 150 Ω typ., R GND Z2 OUT1...4 > typ.; IN low ≈ OUT IN IN(T+) = low signal available. ...

Page 10

... Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET with an approximate solution for R L > 0 Ω: · · Maximum allowable load inductance for a single switch off / j,start = 150° Ω [mH Smart High-Side Power Switch BTS716G ^ · · · i (t) dt ...

Page 11

... Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2,3,4 = low EERII [µA] bb(off) Data Sheet Smart High-Side Power Switch V [ [° BTS716G V1.0, 2007-05-13 ...

Page 12

... Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure 2b: Switching a lamp: Figure 3a: Turn on into short circuit: shut down by overtemperature, restart by cooling off Heating up of the chip may require several milliseconds, depending on external conditions 12 Smart High-Side Power Switch BTS716G V1.0, 2007-05-13 ...

Page 13

... Figure 4a: Overtemperature: Reset if T < Data Sheet Smart High-Side Power Switch Figure 5a: Open load: detection in OFF-state, turn on/off to open load Open load of channel 1; other channels normal operation Figure 6a: Status change after, turn on/off to overtemperature Overtemperature of channel 1; other channels normal operation 13 BTS716G V1.0, 2007-05-13 ...

Page 14

... You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. Data Sheet 2) 0.1 0.2 24x 12.8 -0.2 17 Smart High-Side Power Switch 0.35 x 45˚ 1) 7.6 -0.2 +0.8 0.4 ±0.3 10.3 GPS05094 Dimensions in mm V1.0, 2007-05-13 BTS716G ...

Page 15

... Revision History Version Date Changes 1.0 2007-05-13 Creation of the green datasheet. Data Sheet Smart High-Side Power Switch 18 BTS716G V1.0, 2007-05-13 ...

Page 16

... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...