ITS436L2 Infineon Technologies, ITS436L2 Datasheet
ITS436L2
Specifications of ITS436L2
Available stocks
Related parts for ITS436L2
ITS436L2 Summary of contents
Page 1
... Diagnostic feedback with open drain output Open load detection in ON-state Feedback of thermal shutdown in ON-state Infineon Technologies AG Package 38m 4.75...41V 9.8A 40A -30 …+85°C protection bb Page 1 PROFET ® ITS436L2 PG-TO220-5-11 PG-TO220-5-12 Standard Straight Block Diagram Vbb IN Logic with protection ST functions PROFET ...
Page 2
... Open load detection Function Logic ground case of logical high signal Output to the load Page 2 PROFET ® ITS436L2 VBB OUT LOAD PROFET Pin configuration (top view) Tab = ( GND IN ST OUT 2006-Mar-28 ...
Page 3
... AS IN: ST: Symbol chip - case: R thJC R thJA ) : 5 device on pcb require an external current limit for the GND and status pins (a 150 bb(AZ) 2 (one layer thick) copper area for V Page 3 PROFET ® ITS436L2 Symbol Values Load dump I self-limited L T +150 j -30 … + -40 ...
Page 4
... V j bb(AZ) T =25...+150° =-40...+25° bb(off 150° L(off) bb(off) I GND require an external current limit for the GND and status pins (a 150 bb(AZ) ON(CL) >5 Page 4 PROFET ® ITS436L2 Values min typ max -- 8.8 9 100 200 50 120 250 0 0.1 -- ...
Page 5
... T =150 ° ON(rev (OL IN(T+) V IN(T 0 IN(off IN(on) t after switch off d(ST OL4 +1.6 mA ST(high +1.6 mA ST(low) 2 (one layer thick) copper area for V bb Page 5 PROFET ® ITS436L2 Values min typ max 1 150 -- -- 600 100 -- 900 2.5 3.5 1 0.5 IN( ...
Page 6
... Normal L L operation Open load Overtem perature "Low" Level X = don't care H = "High" Level Status signal after the time delay shown in the diagrams (see fig 5. page 11) Infineon Technologies AG Status BTS 436L2 high impedance, potential depends on external circuit Page 6 PROFET ® ITS436L2 2006-Mar-28 ...
Page 7
... I IN Logic PROFET Z1 GND R GND Signal GND = 47 V typ., R GND Z2 = 3.5 k typ on-state < high I · L(OL) ON Open load Logic detection unit OUT PROFET ST 4 GND GND OUT > low signal available. GND ST ITS436L2 + V bb OUT R Load Load GND = 150 , + OUT IN(T+) 2006-Mar-28 ...
Page 8
... R E Maximum allowable load inductance for a single switch off [mH] L 1000 100 10 0.1 Page 8 PROFET ® OUT PROFET ST GND 2 · · ∫ ON(CL) L · (1+ · · OUT(CL · 150°C,T = 150°C const., L j,start ITS436L2 E Load · i (t) dt · OUT(CL [A] 2006-Mar-28 ...
Page 9
... Typ. on-state resistance high Typ. standby current 9...34 V, IN1,2 = low bb(off bb(off - Infineon Technologies 150°C 25°C -40° [V] bb 100 150 200 T [°C] j Page 9 PROFET ® ITS436L2 2006-Mar-28 ...
Page 10
... L t The initial peak current should be limited by the lamp and not by the current limit of the device. Figure 2c: Switching an inductive load IN ST dV/dtoff t V off OUT L(OL the time constant of load is too large, open-load-status may occur Page 10 PROFET ® ITS436L2 t t 2006-Mar-28 ...
Page 11
... Figure 4a: Overtemperature: Reset if T < OUT T J Infineon Technologies AG Figure 5a: Open load: detection in ON-state, open load occurs in on-state L(SCr d(ST OL) Figure 5b: Open load: turn on/off to open load t Page 11 PROFET ® t d(ST OL) OUT normal open typ d(STOL4 ITS436L2 t d(ST OL) normal t t 2006-Mar-28 ...
Page 12
... Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the ITS436L2 S safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the SP000221232 human body support and/or maintain and sustain and/or protect human life ...