LM86CIMM National Semiconductor, LM86CIMM Datasheet - Page 6

• Manufacturer Part Number: LM86CIMM
• Description: IC DIODE/DGTL TEMP SENSOR 8-MSOP
• Manufacturer: National Semiconductor

Specifications of LM86CIMM

• Function: Hardware Monitor
• Topology: ADC (Sigma Delta), Comparator, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: 0°C ~ 85°C, External Sensor
• Output Type: SMBus™
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: LM86CIMMTR

www.national.com
t
BUF
Symbol
SMBus DIGITAL SWITCHING CHARACTERISTICS Unless otherwise noted, these specifications apply for V
+3.6 Vdc, C
T
cations of the SMBus version 2.0. The following parameters are the timing relationships between SMBCLK and SMBData sig-
nals related to the LM86. They adhere to but are not necessarily the SMBus bus specifications.
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its rated operating conditions.
Note 2: When the input voltage (V
Parasitic components and or ESD protection circuitry are shown in the figure below for the LM86’s pins. The nominal breakdown voltage of D3 is 6.5 V. Care should
be taken not to forward bias the parasitic diode, D1, present on pins: D+, D−. Doing so by more than 50 mV may corrupt a temperature measurements.
Note: An “x” indicates that the diode exists.
Note 3: See the URL ”http://www.national.com/packaging/“ for other recommendations and methods of soldering surface mount devices.
Note 4: Human body model, 100pF discharged through a 1.5kΩ resistor. Machine model, 200pF discharged directly into each pin.
Note 5: Thermal resistance junction-to-ambient when attached to a printed circuit board with 2 oz. foil:
Note 6: Typicals are at T
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
– SOIC-8 = 168˚C/W
– MSOP-8 = 210˚C/W
Pin Name
V
D+
D−
T_CRIT_A
ALERT
SMBData
SMBCLK
A
DD
= T
(V+)
J
= +25˚C, unless otherwise noted. The switching characteristics of the LM86 fully meet or exceed the published specifi-
SMBus Free Time Between Stop and Start
Conditions
L
(load capacitance) on output lines = 80 pF. Boldface limits apply for T
PIN #
A
1
2
3
4
6
7
8
= 25˚C and represent most likely parametric norm.
Parameter
I
) at any pin exceeds the power supplies (V
D1
x
x
FIGURE 1. ESD Protection Input Structure
D2
x
x
SMBus Communication
D3
x
D4
I
x
<
6
Conditions
GND or V
D5
x
x
I
>
V
DD
), the current at that pin should be limited to 5 mA.
D6
x
x
x
x
x
10130313
A
(Note 6)
= T
Typical
R1
x
x
x
x
J
= T
MIN
SNP
to T
(Note 7)
x
x
x
x
Limits
1.3
MAX
; all other limits
DD
=+3.0 Vdc to
ESD CLAMP
10130340
µs (min)
(Limit)
Units
x
x
x