PVZ3G472C01R00 Murata Electronics North America, PVZ3G472C01R00 Datasheet - Page 5

• Manufacturer Part Number: PVZ3G472C01R00
• Description: POT 4.7K OHM 3MM TRIM 1TRN SMD
• Manufacturer: Murata Electronics North America
• Series: PVZ3r

Specifications of PVZ3G472C01R00

• Resistance (ohms): 4.7K
• Power (watts): 0.1W, 1/10W
• Taper: Linear
• Tolerance: ±30%
• Temperature Coefficient: ±500ppm/°C
• Number Of Turns: Single
• Adjustment Type: Top Adjustment
• Mounting Type: Surface Mount
• Resistive Material: Carbon
• Package / Case: Square - 0.122" L x 0.122" W x 0.045" H (3.10mm x 3.10mm x 1.15mm)
• Resistance In Ohms: 4.70K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-4628-2

5.5 High temperature exposure
5.6 Humidity exposure
5.7 Load life
5.8 Humidity load life
5.9 Temperature cycle
5.10 Rotational life
5.11 Vibration
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the
trimmer potentiometer should be kept in a chamber at 70±2°C without loading for 500±12 hours. The
resistance value should be measured after keeping the trimmer potentiometer in a room for 1.5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that,
the trimmer potentiometer should be kept in a chamber at 40±2°C and 90 to 95% without loading for 500±12
hours. The resistance value should be measured after keeping the trimmer potentiometer in a room for 5±1/6
hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the
trimmer potentiometer should be kept in a chamber at 50±2°C with loading the 1/2 rated voltage between #1
and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12 hours. The resistance value
should be measured after keeping the trimmer potentiometer in a room for 1.5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the
trimmer potentiometer should be kept in a chamber at 40±2°C and 90 to 95% with loading the 1/2 rated voltage
between #1 and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12hours.
The resistance value should be measured after keeping the trimmer potentiometer in a room for 5±1/6 hours.
The wiper contact point should be preset at about
50% position of effective rotational angle. After that,
the trimmer potentiometer should be subjected to
Table 2 temperatures for 5 cycles. The resistance
value should be measured after keeping the trimmer
potentiometer in a room for 1.5±1/6 hours.
The wiper should be rotated over 90% of the effective rotational angle without loading at a speed of 10 cycles
per minute, for 10 cycles continuously. The resistance value should be measured after keeping the trimmer
potentiometer in a room for 10±5 minutes.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the
trimmer potentiometer should be tested under the condition of the amplitude of 1.5mm, the frequency range
from 10 to 55Hz (shall be traversed in approximately one minute) and 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hours)
UNCONTROLLED
REFERENCE ONLY
COPY
Time (min.)
Temp. (°C)
Sequence
SPECIFICATION No. JVR03Z-7148B
-25±3
30±3
1
Table 2
10 max.
+25±2
2
+85±3
30±3
3
10 max.
+25±2
4
5/12