PVZ3G472C01R00 Murata Electronics North America, PVZ3G472C01R00 Datasheet - Page 8

• Manufacturer Part Number: PVZ3G472C01R00
• Description: POT 4.7K OHM 3MM TRIM 1TRN SMD
• Manufacturer: Murata Electronics North America
• Series: PVZ3r

Specifications of PVZ3G472C01R00

• Resistance (ohms): 4.7K
• Power (watts): 0.1W, 1/10W
• Taper: Linear
• Tolerance: ±30%
• Temperature Coefficient: ±500ppm/°C
• Number Of Turns: Single
• Adjustment Type: Top Adjustment
• Mounting Type: Surface Mount
• Resistive Material: Carbon
• Package / Case: Square - 0.122" L x 0.122" W x 0.045" H (3.10mm x 3.10mm x 1.15mm)
• Resistance In Ohms: 4.70K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-4628-2

7.5 Operating environmental conditions
7.6 Storage Conditions
7.7 Circuit design guide
8.
The trimmer potentiometer should not be used under the following environmental conditions.
If you use the trimmer potentiometer in an environment other than listed below, please consult with a Murata
factory representative prior to using.
(1) Corrosive gaseous atmosphere. ( e,g. Cl
(2) In liquid. ( Ex. Water, Oil, Medical liquid, Organic solvent, etc)
(3) Dusty/dirty atmosphere.
(4) Direct sunlight.
(5) No static voltage or electric/magnetic fields.
(6) Direct sea breeze.
(7) Other variations of the above.
(1) To ensure the solderability of the terminal, store that the temperature is -10 to +40°C and the relative
(2) Do not store in or near corrosive gases.
(3) Do not store under direct sunlight.
(1) Please confirm specifications of required trimmer potentiometers (power rating, maximum operating
(2) When using with partial load (rheostat), minimize the power depending on the resistance value.
(3) If the trimmer potentiometer is used in DC and high humidity conditions, please connect wiper (#2) for
(4) Use trimmer potentiometer within 90% of the effective-electrical rotational angle to prevent a sudden
(5) The maximum input voltage to a trimmer potentiometer should not exceed (P R)^ 1/2 or the maximum
(6) If the mounting process includes reflow soldering for the upper side of the PCB and flow soldering for its
(1)Please make sure that your product has been evaluated in view of your specifications with our product
(2) You are requested not to use our product deviating from the agreed specifications.
(3) Please return one duplicate of this product specification to us with your receipt signature. If the duplicate is
(4) We consider it is not appropriate to include any terms and conditions with regard to the business
humidity is 30 to 85% RH, and use within six months after delivery. If you are going to use a product that
has been stored for more than six months, please check its solderability beforehand.
voltage, operating temperature, etc.).
plus and resistive element (#1 or #3) for minus.
change of resistance when excessive current is applied.
operating voltage, whichever is smaller.
lower side and a product is mounted on the upper side by reflow soldering without cleaning, take the
following cautions in order to prevent the flux from flowing onto the wiper sliding surface.
being mounted to your product.
not returned, this product specification will be deemed to have been received by you.
Notice
transaction in the product specifications, drawings or other technical documents. Therefor, if your
technical documents as above include such terms and conditions such as warranty clause, product
liability clause, or intellectual property infringement liability clause, they will be deemed to be invalid.
1. Don't place the product within 10 mm from the outer edge of the PCB.
2. Don't provide a through hole near the product.
(A distance of 10 mm or more between the product and a through hole is necessary.)
UNCONTROLLED
REFERENCE ONLY
COPY
,
H S,NH
,
SO
,
NO etc)
*P: Power rating (W)
R: Normal resistance value (ohm)
SPECIFICATION No. JVR03Z-7148B
+
-
#2
#1
#3
8/12