PVZ3G472C01R00 Murata Electronics North America, PVZ3G472C01R00 Datasheet - Page 7

• Manufacturer Part Number: PVZ3G472C01R00
• Description: POT 4.7K OHM 3MM TRIM 1TRN SMD
• Manufacturer: Murata Electronics North America
• Series: PVZ3r

Specifications of PVZ3G472C01R00

• Resistance (ohms): 4.7K
• Power (watts): 0.1W, 1/10W
• Taper: Linear
• Tolerance: ±30%
• Temperature Coefficient: ±500ppm/°C
• Number Of Turns: Single
• Adjustment Type: Top Adjustment
• Mounting Type: Surface Mount
• Resistive Material: Carbon
• Package / Case: Square - 0.122" L x 0.122" W x 0.045" H (3.10mm x 3.10mm x 1.15mm)
• Resistance In Ohms: 4.70K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-4628-2

7. Caution for Using
7.1 Mounting the product
7.2 Soldering
7.3 Cleaning
7.4 Adjusting
Please use a pick-up nozzle with 2.5 to 2.8mm outer dia., 2mm inner dia.
(1) Standard soldering condition for lead-free solder (96.5Sn-3.0Ag-0.5Cu)
(2) The amount of solder is critical. The thickness of solder paste should be printed from 100µm to 150µm
(3) The soldering iron should not come in contact with the resin substrate of the trimmer potentiometer.
(4) PVZ3 series can not be flow soldering. If you use the flow soldering method, the trimmer potentiometer
(5) Trimmer potentiometer is designed for the purpose of soldering. If you intend to connect with conductive
In case there is flux on the resistive element, clean sufficiently by cleaning solvents and remove all residual
flux perfectly. When cleaning the trimmer potentiometer, only use Isopropyl-alcohol and Ethyl-alcohol.
If you use any other types of solvents, please evaluate performance by your set. Moreover, please confirm
no damage for trimmer potentiometer after cleaning by your conditions.
(1) PVZ3 series dose not have a mechanical stop for over rotation, so please use within the effective
(2) Please use suitable screwdrivers that fit comfortably in driver slot. We recommend the screwdrivers
(3) When using a lock paint to fix adjustment position, please evaluate performance by your set.
245
220
180
150
100
Before using other soldering conditions than those listed above, please consult with a Murata factory
representative prior to using. If the soldering conditions are not suitable, e.g., excessive time and/or
excessive temperature, the trimmer potentiometer may deviate from the specified characteristics.
and the dimension of land pattern should be used Murata’s standard land pattern at re-flow soldering.
Insufficient amounts of solder can lead to insufficient soldering strength on the PCB.
If such contact does occur, the trimmer potentiometer may be damaged.
may not function.
adhesive or other method, please consult with a Murata factory representative prior to using.
rotational angle. The #2 terminal is opened electrically out of effective rotational angle.
below.
Lock paint may become the cause of corrosion and contact fault.
0
Excessive amounts of solder may cause the bridging between the terminals or the contact failure due
to flux wicking up.
VESSEL MFG.
VESSEL MFG.
Manufactures
Pre-heating(in the air)
60 to 120 sec.
Reflow soldering
(Melting zone)
30 to 60 sec.
Soldering
UNCONTROLLED
REFERENCE ONLY
Gradual cooling
COPY
(in the air)
NO.9000 1.8x30
NO.9000+1.7x30
Model Number
Time
Temperature of tip
Diameter
Soldering time
Wattage of iron
SPECIFICATION No. JVR03Z-7148B
MURATA Model Number
Soldering iron
KMDR080
KMDR110
: 360°C max.
: 2mm max.
: 3 sec. max.
: 30W max.
7/12