AXB030X43-SRZ Lineage Power, AXB030X43-SRZ Datasheet - Page 10

• Manufacturer Part Number: AXB030X43-SRZ
• Description: CONVERTER DC/DC 3-6V 30W SMD
• Manufacturer: Lineage Power
• Series: Austin Lynx™r
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of AXB030X43-SRZ

• Output: 3 ~ 6V
• Number Of Outputs: 1
• Power (watts): 30W
• Mounting Type: Surface Mount
• Voltage - Input: 18 ~ 30V
• Package / Case: 6-SMD Module
• 1st Output: 3 ~ 6 VDC @ 10A
• Size / Dimension: 1.30" L x 0.53" W x 0.33" H (33mm x 13.5mm x 8.3mm)
• Power (watts) - Rated: 30W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 91%
• Approvals: CSA, EN, UL, VDE
• Output Power: 60 W
• Input Voltage Range: 18 V to 30 V
• Output Voltage (channel 1): 3 V to 6 V
• Output Current (channel 1): 10 A
• Package / Case Size: SMD
• Output Type: Non-Isolated
• Output Voltage: 3 V to 6 V
• Product: Non-Isolated / POL
• Output Current: 10A
• Input Voltage: 24V
• Screening Level: Industrial
• Product Length (mm): 33mm
• Product Depth (mm): 13.46mm
• Mounting Style: Surface Mount
• Pin Count: 6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 555-1106-2; CC109106738

Data Sheet
December 18, 2009
Test Configurations
Figure 25. Input Reflected Ripple Current Test
Setup.
Figure 26. Output Ripple and Noise Test Setup.
Figure 27. Output Voltage and Efficiency Test Setup.
LINEAGE
NOTE: All voltage measurements to be taken at the module
V
COM
O
Efficiency
(+)
TO OSCILLOSCOPE
NOTE: Measure input reflected ripple current with a simulated
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
R
R
NOTE: All voltage measurements to be taken at the module
distribution
distribution
POWER
source inductance (L
possible battery impedance. Measure current as shown
above.
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
R
R
contact
contact
η =
COPPER STRIP
1uF
@ 20°C 100kHz
E.S.R.<0.1Ω
C
S
.
L
220μF
V
1μH
TEST
IN
V
V
V
COM
IN
IN
O
TEST
GROUND PLANE
(+)
. I
. I
) of 1μH. Capacitor C
O
IN
10uF
COM
V
O
V
150μF
C
x 100 %
O
Min
IN
SCOPE
CURRENT PROBE
18/20– 30/32Vdc input; 3 – 6Vdc & 5 – 15Vdc Output; 30/50W
R
R
contact
contact
S
offsets
V
COM
IN
(+)
RESISTIVE
R
R
LOAD
distribution
distribution
R
LOAD
Austin Lynx
Design Considerations
Input Filtering
The Austin Lynx
connected to a low-impedance source. A highly
inductive source can affect the stability of the module.
An input capacitance must be placed directly adjacent
to the input pin of the module, to minimize input ripple
voltage and ensure module stability.
Output Filtering
The Austin Lynx
output ripple voltage and will meet the maximum output
ripple specification with 1 µF ceramic and 10 µF
tantalum capacitors at the output of the module.
However, additional output filtering may be required by
the system designer for a number of reasons. First,
there may be a need to further reduce the output ripple
and noise of the module. Second, the dynamic
response characteristics may need to be customized to
a particular load step change.
To reduce the output ripple and improve the dynamic
response to a step load change, additional capacitance
at the output can be used. Low ESR polymer and
ceramic capacitors are recommended to improve the
dynamic response of the module. For stable operation
of the module, limit the capacitance to less than the
maximum output capacitance as specified in the
electrical specification table.
Safety Considerations
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards,
i.e., UL 60950, CSA C22.2 No. 60950-00, EN60950
(VDE 0850) (IEC60950, 3
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power
module has extra-low voltage (ELV) outputs when all
inputs are ELV.
TM
24V: Non-isolated Power Modules:
TM
TM
24V SMT module should be
24V SMT module is designed for low
rd
edition) Licensed.
10