EVAL-AD5447EBZ Analog Devices Inc, EVAL-AD5447EBZ Datasheet - Page 19

• Manufacturer Part Number: EVAL-AD5447EBZ
• Description: BOARD EVALUATION FOR AD5447
• Manufacturer: Analog Devices Inc

Specifications of EVAL-AD5447EBZ

• Number Of Dac's: 2
• Number Of Bits: 12
• Outputs And Type: 2, Single Ended
• Sampling Rate (per Second): 21.3M
• Data Interface: Parallel
• Settling Time: 80ns
• Dac Type: Current
• Voltage Supply Source: Single
• Operating Temperature: -40°C ~ 125°C
• Utilized Ic / Part: AD5447
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SINGLE-SUPPLY APPLICATIONS
Voltage-Switching Mode
Figure 40 shows the DACs operating in voltage-switching
mode. The reference voltage, V
and the output voltage is available at the V
configuration, a positive reference voltage results in a positive
output voltage, making single-supply operation possible. The
output from the DAC is voltage at constant impedance (the
DAC ladder resistance). Therefore, an op amp is necessary to
buffer the output voltage. The reference input no longer sees
constant input impedance, but one that varies with code.
Therefore, the voltage input should be driven from a low
impedance source.
Note that V
the DAC ladder no longer have the same source-drain drive
voltage. As a result, their on resistance differs and degrades the
integral linearity of the DAC. Also, V
more than 0.3 V, or an internal diode turns on, causing the
device to exceed the maximum ratings. In this type of
application, the full range of multiplying capability of the DAC
is lost.
Positive Output Voltage
The output voltage polarity is opposite to the V
dc reference voltages. To achieve a positive voltage output, an
applied negative reference to the input of the DAC is preferred
over the output inversion through an inverting amplifier
because of the resistor’s tolerance errors. To generate a negative
reference, the reference can be level-shifted by an op amp such
that the V
ground and –2.5 V, respectively, as shown in Figure 41.
V
IN
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
OUT
IF A1 IS A HIGH SPEED AMPLIFIER.
Figure 40. Single-Supply Voltage-Switching Mode
IN
I
AGND
OUT
and GND pins of the reference become the virtual
is limited to low voltages because the switches in
A
R
FB
A
GND
V
V
DD
DD
V
REF
IN
A
, is applied to the I
R1
IN
must not go negative by
REF
A terminal. In this
R2
REF
polarity for
OUT
V
A pin,
OUT
Rev. B | Page 19 of 32
ADDING GAIN
In applications where the output voltage must be greater than
V
it can be achieved in a single stage. Consider the effect of temper-
ature coefficients of the thin film resistors of the DAC. Simply
placing a resistor in series with the R
in the temperature coefficients, resulting in larger gain temper-
ature coefficient errors. Instead, the circuit in Figure 42 shows
the recommended method for increasing the gain of the circuit.
R1, R2, and R3 should have similar temperature coefficients,
but they need not match the temperature coefficients of the
DAC. This approach is recommended in circuits where gains of
greater than 1 are required.
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
V
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IN
IN
IF A1 IS A HIGH SPEED AMPLIFIER.
IF A1 IS A HIGH SPEED AMPLIFIER.
, gain can be added with an additional external amplifier, or
R1
Figure 41. Positive Voltage Output with Minimum Components
+5V
–5V
–2.5V
V
V
Figure 42. Increasing Gain of Current Output DAC
REF
ADR03
OUT
GND
8-/10-/12-BIT
A
V
V
V
GND
IN
DAC
DD
DD
V
REF
8-/10-/12-BIT
A
V
R
DD
I
AGND
AD5428/AD5440/AD5447
FB
GND
OUT
V
DAC
DD
= 5V
A
A
R
I
AGND
FB
FB
OUT
C1
A
resistor causes mismatches
A
R3
R2
C1
GAIN =
R
1
=
R2
R2R3
V
0V to 2.5V
OUT
R2 + R3
V
+
OUT
R3
R2
=