V23816-N1018-L312 Infineon Technologies, V23816-N1018-L312 Datasheet
V23816-N1018-L312
Specifications of V23816-N1018-L312
Related parts for V23816-N1018-L312
V23816-N1018-L312 Summary of contents
Page 1
... LVTTL Output Source Current ........................................... 1 mA Operating Ambient Temperature ................................ Storage Ambient Temperature ............................... – °C Static Discharge Voltage, All Pins ................................... 1000 V (*) Ordering Information Connector type SC LC Preliminary V23816-N1018-L312 ).................................................... 0 to 4.0 V Fiber length Part number 24.1 0.8 “ V23816-N1018-C312 24.1 0.8 “ V23816-N1018-L312 MAY 2001 (*) ...
Page 2
... The PIN/Preamp contains a PIN photodiode, trans-impedance amplifier and non-limiting post-amplifier in one package. The PIN diode produces a current output, which is directly propor- tional to the intensity of the incoming light. The trans-imped- V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 2 ...
Page 3
... TX electrical inputs. Jitter Transfer is defined to be less than 0 MHz, then dropping at –20 dB decade thereafter, per ITU-T G.958 and Bellcore GR-253. The Jitter Transfer must be less than the following mask limits. V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 3 ...
Page 4
... Transceiver IC. DC coupled and internally TX_BIASMON LVTTL biased. Phase Initialization. Rising edge of PHASE_INITP will realign internal timing. DC coupled. No internal termi- nation. V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 4 622 MHz Pclk TXFault BiasMonitor Laser Diode OC-48 1300 nm ...
Page 5
... Receive power monitor output. A voltage output which is directly proportional to the optical RX input power. V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 5 Level I/O Pin # Description 38 Line Loopback Enable input. A Low level enables Line Loopback mode. When active, the RX inputs to the Transceiver IC will be routed directly to the TX outputs ...
Page 6
... Voltage 15 mV 0-p LVTTL Input Low Voltage LVTTL Input High Current LVTTL Output Current LVTTL Output High Voltage LVTTL Output Low Voltage V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 6 Symbol Min. Typ. Max. Units LVDS V 1.1 1 LVDS V 0.6 1.5 ...
Page 7
... T CASE is measured on top of the transponder (see details on page 1, 1 ps, rms 2. Maximum allowable jitter on the reference clock input (REFCLKP/N) 3.2 ns 622.08 MHz V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 7 Sym- Condi- Min. Typ. bol tions 40 20-80% 100 T See RX SR Timing Dia- gram T ...
Page 8
... The RX_LOS output is an active high LVTTL output, which is set HIGH if there is a loss of RX optical signal input (LOS), A decrease in optical input power below the assert level will cause the RX_LOS V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 8 Symbol Min ...
Page 9
... VCC 0,8 VCC 0,6 VCC VCC 0,4 VCC 0,2 RESET_L 0 RX_MON -25 SPARE V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 9 Standard Comments EIA/JESD22-A114-A Class 1 (2000 V) (MIL-STD 883D Method 3015.7) EN 61000-4-2 Discharges ranging IEC 61000-4-2 from housing/pigtails cause no damage to transponder (under recommended condi- tions) ...
Page 10
... PHASE_INITN is directly connected to PHASE_ERRN. These connections must be made on the customer board. The REFCLK input is a LVPECL input, which is driven by the customer Clock Source, which should be an LVPECL device. DC V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km 10 differential between lines in the transponder. to ground termination in the ...
Page 11
... QSH connector. Hostboard Contact Area to ground termina- Dimensions in mm [inches] dif- characteristic character- o polish. The minimum For detailed connector layout information, check http://www.samtec.com, and go to “QSH” connector. V23816-N1018-C/L312, 3.3V, 4-Line LVDS Parallel 2.5GBd Transp.OC-48 SONET/SDH SR, 2km ...
Page 12
... Infineon Technologies AG • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany Infineon Technologies, Inc. • Fiber Optics • 1730 North First Street • San Jose, CA 95112, USA Infineon Technologies K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku • Tokyo 141, Japan Scheme of tightening mounting screws It is recommended to use a torque wrench to tighten the mounting screws ...