ATTINY2313V-10PU Atmel, ATTINY2313V-10PU Datasheet - Page 27

• Manufacturer Part Number: ATTINY2313V-10PU
• Description: IC MCU AVR 2K FLASH 20DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313V-10PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI/UART/USI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Package: 20PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 10 MHz
• Data Rom Size: 128 B
• Height: 4.95 mm
• Length: 26.92 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Width: 7.11 mm
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

External Clock
2543L–AVR–08/10
To drive the device from an external clock source, XTAL1 should be driven as shown in
13. To run the device on an external clock, the CKSEL Fuses must be programmed to “0000”.
Figure 13. External Clock Drive Configuration
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 9. Crystal Oscillator Clock Frequency
Table 10. Start-up Times for the External Clock Selection
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the
MCU is kept in Reset during such changes in the clock frequency.
Note that the System Clock Prescaler can be used to implement run-time changes of the internal
clock frequency while still ensuring stable operation.
CKSEL3..0
0000 - 0001
SUT1..0
00
01
10
11
10.
Start-up Time from Power-
down and Power-save
6 CK
6 CK
6 CK
EXTERNAL
SIGNAL
CLOCK
NC
Frequency Range
0 - 16 MHz
Additional Delay from
Reset (V
Reserved
14CK + 4.1 ms
14CK + 65 ms
14CK
CC
= 5.0V)
XTAL2
XTAL1
GND
BOD enabled
Fast rising power
Recommended Usage
Slowly rising power
Figure
27