ATMEGA48PV-10MU Atmel, ATMEGA48PV-10MU Datasheet - Page 35

• Manufacturer Part Number: ATMEGA48PV-10MU
• Description: MCU AVR 4K ISP FLASH 10MHZ 32QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA48PV-10MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.7
8.8
8025L–AVR–7/10
128 kHz Internal Oscillator
External Clock
The 128 kHz internal Oscillator is a low power Oscillator providing a clock of 128 kHz. The fre-
quency is nominal at 3V and 25°C. This clock may be select as the system clock by
programming the CKSEL Fuses to “11” as shown in
Table 8-13.
Note:
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 8-14.
Note:
To drive the device from an external clock source, XTAL1 should be driven as shown in
8-4 on page
to “0000” (see
Table 8-15.
Figure 8-4.
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
BOD enabled
Fast rising power
Slowly rising power
Power Conditions
8-14.
8-16.
1. Note that the 128 kHz oscillator is a very low power clock source, and is not designed for a
1. If the RSTDISBL fuse is programmed, this start-up time will be increased to
high accuracy.
14CK + 4.1 ms to ensure programming mode can be entered.
35. To run the device on an external clock, the CKSEL Fuses must be programmed
128 kHz Internal Oscillator Operating Modes
Start-up Times for the 128 kHz Internal Oscillator
Table
Crystal Oscillator Clock Frequency
External Clock Drive Configuration
Nominal Frequency
8-15).
Frequency
0 - 20 MHz
EXTERNAL
128 kHz
SIGNAL
CLOCK
Start-up Time from Power-
down and Power-save
NC
(1)
Reserved
6 CK
6 CK
6 CK
Table
ATmega48P/88P/168P
XTAL2
XTAL1
GND
8-13.
Additional Delay from
14CK + 64 ms
14CK + 4 ms
14CK
Reset
CKSEL[3:0]
CKSEL[3:0]
(1)
0011
0000
SUT[1:0]
Figure
00
01
10
11
35