DSPIC30F2011-20I/P Microchip Technology, DSPIC30F2011-20I/P Datasheet - Page 8
![IC DSPIC MCU/DSP 12K 18DIP](/photos/6/76/67657/18-dip_300mil__sml.jpg)
DSPIC30F2011-20I/P
Manufacturer Part Number
DSPIC30F2011-20I/P
Description
IC DSPIC MCU/DSP 12K 18DIP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20ISO.pdf
(210 pages)
3.DSPIC30F2011-20ISO.pdf
(14 pages)
4.DSPIC30F2011-20ISO.pdf
(6 pages)
5.DSPIC30F2011-20ISO.pdf
(18 pages)
6.DSPIC30F2011-20IP.pdf
(26 pages)
7.DSPIC30F2011-20IP.pdf
(206 pages)
Specifications of DSPIC30F2011-20I/P
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
12
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 8x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
18-DIP (0.300", 7.62mm)
Core Frequency
40MHz
Core Supply Voltage
5.5V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
12
Flash Memory Size
12KB
Supply Voltage Range
2.5V To 5.5V
Package
18PDIP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
20 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
12
Interface Type
I2C/SPI/UART
On-chip Adc
8-chx12-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC30F005 - MODULE SCKT DSPIC30F 18DIP/SOICACICE0202 - ADAPTER MPLABICE 18P 300 MIL
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
DSPIC30F2011-20IP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DSPIC30F2011-20I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
5.5.3
Once code memory is programmed, the contents of
memory can be verified to ensure that programming
was successful. Verification requires code memory to
be read back and compared against the copy held in
the programmer’s buffer.
The READP command can be used to read back all the
programmed code memory.
Alternatively, you can have the programmer perform
the verification once the entire device is programmed
using a checksum computation, as described in
Section 6.8 “Checksum
5.6
5.6.1
The panel architecture for the data EEPROM memory
array consists of 128 rows of sixteen 16-bit data words.
Each panel stores 2K words. All devices have either
one or no memory panels. Devices with data EEPROM
provide either 512 words, 1024 words or 2048 words of
memory on the one panel (see
TABLE 5-3:
DS70102K-page 8
dsPIC30F2010
dsPIC30F2011
dsPIC30F2012
dsPIC30F3010
dsPIC30F3011
dsPIC30F3012
dsPIC30F3013
dsPIC30F3014
dsPIC30F4011
dsPIC30F4012
dsPIC30F4013
dsPIC30F5011
dsPIC30F5013
dsPIC30F5015
dsPIC30F5016
dsPIC30F6010
dsPIC30F6010A
dsPIC30F6011
dsPIC30F6011A
dsPIC30F6012
dsPIC30F6012A
dsPIC30F6013
dsPIC30F6013A
dsPIC30F6014
dsPIC30F6014A
dsPIC30F6015
Device
Data EEPROM Programming
PROGRAMMING VERIFICATION
OVERVIEW
DATA EEPROM SIZE
Data EEPROM
Size (Words)
Computation”.
2048
2048
1024
1024
2048
2048
1024
1024
2048
2048
2048
512
512
512
512
512
512
512
512
512
512
512
512
512
0
0
Table
5-3).
Number of
Rows
128
128
128
128
128
128
128
32
32
32
32
32
32
32
32
32
32
32
32
32
64
64
64
64
0
0
5.6.2
The programming executive uses the PROGD command
to program the data EEPROM.
the flowchart of the process. Firstly, the number of rows
to program (RemainingRows) is based on the device
size, and the destination address (DestAddress) is set
to ‘0’. In this example, 128 rows (2048 words) of data
EEPROM will be programmed.
The first PROGD command programs the first row of
data EEPROM. Once the command completes
successfully, ‘RemainingRows’ is decremented by 1
and compared with 0. Since there are 127 more rows
to program, ‘BaseAddress’ is incremented by 0x20 to
point to the next row of data EEPROM. This process is
then repeated until all 128 rows of data EEPROM are
programmed.
FIGURE 5-4:
BaseAddress =
BaseAddress
+ 0x20
PROGRAMMING METHODOLOGY
No
Remaining Rows = 128
RemainingRows – 1
RemainingRows =
BaseAddress = 0
PROGD
Command with
RemainingRows
FLOWCHART FOR
PROGRAMMING
dsPIC30F6014A DATA
EEPROM
Send
BaseAddress
© 2010 Microchip Technology Inc.
PASS?
Finish
Start
0?
PROGD
Is
Is
response
Yes
Yes
Figure 5-4
Report Error
No
Failure
illustrates