PIC16F737-I/SP Microchip Technology, PIC16F737-I/SP Datasheet - Page 417

• Manufacturer Part Number: PIC16F737-I/SP
• Description: IC PIC MCU FLASH 4KX14 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F737-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 25
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: AUSART/CCP/I2C/MSSP/SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 3
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3DBF777 - BOARD DAUGHTER ICEPIC3
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Section 22. Basic 8-bit A/D Converter
22.8
A/D Accuracy/Error
In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate
to high frequencies, T
should be derived from the device oscillator.
AD
The absolute accuracy specified for the A/D converter includes the sum of all contributions for
quantization error, integral error, differential error, full scale error, offset error, and monotonicity.
It is defined as the maximum deviation from an actual transition versus an ideal transition for any
code. The absolute error of the A/D converter is specified at < 1 LSb for V
= V
(over the
DD
REF
device’s specified operating range). However, the accuracy of the A/D converter will degrade as
V
diverges from V
.
DD
REF
For a given range of analog inputs, the output digital code will be the same. This is due to the
quantization of the analog input to a digital code. Quantization error is typically
1/2 LSb and is
22
inherent in the analog to digital conversion process. The only way to reduce quantization error is
to increase the resolution of the A/D converter.
Offset error measures the first actual transition of a code versus the first ideal transition of a code.
Offset error shifts the entire transfer function. Offset error can be calibrated out of a system or
introduced into a system through the interaction of the total leakage current and source imped-
ance at the analog input.
Gain error measures the maximum deviation of the last actual transition and the last ideal tran-
sition adjusted for offset error. This error appears as a change in slope of the transfer function.
The difference in gain error to full scale error is that full scale does not take offset error into
account. Gain error can be calibrated out in software.
Linearity error refers to the uniformity of the code changes. Linearity errors cannot be calibrated
out of the system. Integral non-linearity error measures the actual code transition versus the ideal
code transition adjusted by the gain error for each code.
Differential non-linearity measures the maximum actual code width versus the ideal code width.
This measure is unadjusted.
The maximum pin leakage current is specified in the Device Data Sheet electrical specification
parameter
D060.
In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate
to high frequencies, T
should be derived from the device oscillator. T
must not violate the
AD
AD
minimum and should be minimized to reduce inaccuracies due to noise and sampling capacitor
bleed off.
In systems where the device will enter SLEEP mode after the start of the A/D conversion, the RC
clock source selection is required. In this mode, the digital noise from the modules in SLEEP are
stopped. This method gives high accuracy.
1997 Microchip Technology Inc.
DS31022A-page 22-15