PIC18F2510-I/SP Microchip Technology, PIC18F2510-I/SP Datasheet - Page 3

• Manufacturer Part Number: PIC18F2510-I/SP
• Description: IC MCU FLASH 16KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2510-I/SP

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 25
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Power-Managed Modes:
• Run: CPU On, Peripherals On
• Idle: CPU Off, Peripherals On
• Sleep: CPU Off, Peripherals Off
• Idle mode Currents Down to 3.0 μA Typical
• Sleep mode Currents Down to 20 nA Typical
• Timer1 Oscillator: 1.8 μA, 32 kHz, 2V
• Watchdog Timer: 2.1 μA
• Two-Speed Oscillator Start-up
Peripheral Highlights:
• High-Current Sink/Source 25 mA/25 mA
• Up to 2 Capture/Compare/PWM (CCP) modules,
• Enhanced Capture/Compare/PWM (ECCP)
• Master Synchronous Serial Port (MSSP) module
• Enhanced Addressable USART module:
• 10-Bit, Up to 13-Channel Analog-to-Digital
• Dual Analog Comparators with Input Multiplexing
• Programmable 16-Level High/Low-Voltage
© 2007 Microchip Technology Inc.
One with Auto-Shutdown (28-pin devices)
module (40/44-pin devices only):
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-shutdown and auto-restart
Supporting 3-Wire SPI (all 4 modes) and I
Master and Slave modes
- Supports RS-485, RS-232 and LIN 1.2
- RS-232 operation using internal oscillator
- Auto-wake-up on Start bit
- Auto-Baud Detect
Converter module (A/D):
- Auto-acquisition capability
- Conversion available during Sleep
Detection (HLVD) module:
- Supports interrupt on High/Low-Voltage Detection
block (no external crystal required)
28/40/44-Pin Flash Microcontrollers with
10-Bit A/D and nanoWatt Technology
PIC18F2X1X/4X1X
2
C™
Preliminary
Flexible Oscillator Structure:
• Four Crystal modes, Up to 40 MHz
• 4x Phase Lock Loop (PLL) – Available for Crystal
• Two External RC modes, Up to 4 MHz
• Two External Clock modes, Up to 40 MHz
• Internal Oscillator Block:
• Secondary Oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor:
Special Microcontroller Features:
• C Compiler Optimized Architecture:
• 100,000 Erase/Write Cycle Flash Program
• Three Programmable External Interrupts
• Four Input Change Interrupts
• Priority Levels for Interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
• Single-Supply 5V In-Circuit Serial
• In-Circuit Debug (ICD) via Two Pins
• Wide Operating Voltage Range: 2.0V to 5.5V
• Programmable Brown-out Reset (BOR) with
and Internal Oscillators
- 8 user-selectable frequencies, from 31 kHz to
- Provides a complete range of clock speeds
- User-tunable to compensate for frequency drift
- Allows for safe shutdown if peripheral clock stops
- Optional extended instruction set designed to
Memory Typical
- Programmable period from 4 ms to 131s
Programming™ (ICSP™) via Two Pins
Software Enable Option
8 MHz
from 31 kHz to 32 MHz when used with PLL
optimize re-entrant code
DS39636C-page 1