ATMEGA3250PV-10AU Atmel, ATMEGA3250PV-10AU Datasheet - Page 145

• Manufacturer Part Number: ATMEGA3250PV-10AU
• Description: IC MCU AVR 32K FLASH 100-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA3250PV-10AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SPI, UART, USI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Data Rom Size: 1 KB
• Operating Supply Voltage: 1.8 V to 5.5 V
• Operating Temperature Range: - 40 C to + 85 C
• A/d Bit Size: 10 bit
• A/d Channels Available: 8
• Height: 1 mm
• Length: 14 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Width: 14 mm
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK504 - STARTER KIT AVR EXP MOD 100P LCD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATMEGA3250PV-8AU; ATMEGA3250PV-8AU

16.8
8023F–AVR–07/09
Timer/Counter Timing Diagrams
• The timer starts counting from a value higher than the one in OCR2A, and for that reason
The following figures show the Timer/Counter in synchronous mode, and the timer clock (clk
is therefore shown as a clock enable signal. In asynchronous mode, clk
the Timer/Counter Oscillator clock. The figures include information on when Interrupt Flags are
set.
count sequence close to the MAX value in all modes other than phase correct PWM mode.
Figure 16-8. Timer/Counter Timing Diagram, no Prescaling
Figure 16-9
Figure 16-9. Timer/Counter Timing Diagram, with Prescaler (f
Figure 16-10
symmetry around BOTTOM the OCn value at MAX must correspond to the result of an up-
counting Compare Match.
misses the Compare Match and hence the OCn change that would have happened on the way
up.
Figure 16-8
TCNTn
(clk
TCNTn
(clk
TOVn
TOVn
clk
clk
clk
clk
I/O
I/O
I/O
Tn
I/O
Tn
/1)
/8)
shows the same timing data, but with the prescaler enabled.
shows the setting of OCF2A in all modes except CTC mode.
contains timing data for basic Timer/Counter operation. The figure shows the
MAX - 1
MAX - 1
MAX
MAX
ATmega325P/3250P
BOTTOM
BOTTOM
clk_I/O
/8)
I/O
should be replaced by
BOTTOM + 1
BOTTOM + 1
145
T2
)