AT91SAM7L128-CU Atmel, AT91SAM7L128-CU Datasheet - Page 171

• Manufacturer Part Number: AT91SAM7L128-CU
• Description: MCU ARM7 128K HS FLASH 144-LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7L128-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 36MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 1.55 V ~ 1.8 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LFBGA
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 6 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM7L-STK - KIT EVAL FOR AT91SAM7LAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

20.3.4.5
20.3.4.6
20.3.4.7
6257A–ATARM–20-Feb-08
Flash General-purpose NVM Commands
Flash Security Bit Command
Memory Write Command
General-purpose NVM bits (GP NVM) can be set with the Set GPNVM command (SGPB). Using
this command, several GP NVM bits can be activated at the same time. Bit 0 of Bit Mask corre-
sponds to the first GPNVM bit and so on.
In the same way, the Clear GPNVM command (CGPB) is used to clear GP NVM bits. All the
general-purpose NVM bits are also cleared by the EA command.
Table 20-23. Set and Clear General-purpose NVM Bit Command
GP NVM bits can be read using Get GPNVM Bit command (GGPB). When a bit set in the Bit
Mask is returned, then the corresponding GPNVM bit is set.
Table 20-24. Get General-purpose NVM Bit Command
Security bits can be set using Set Security Bit command (SSE). Once the security bit is active,
the Fast Flash programming is disabled. No other command can be run. Only an event on the
Erase pin can erase the security bit once the contents of the Flash have been erased.
Table 20-25. Set Security Bit Command
Once the security bit is set, it is not possible to access FFPI. The only way to erase the security
bit is to erase the Flash.
In order to erase the Flash, the user must perform the following:
Then it is possible to return to FFPI mode and check that Flash is erased.
This command is used to perform a write access to any memory location.
The Memory Write command (WRAM) is optimized for consecutive writes. An internal address
buffer is automatically increased.
Read/Write
Write
Write
Read/Write
Write
Read
Read/Write
Write
• Power-off the chip
• Power-on the chip with TST = 0 and FWUP=0
• Assert Erase during a period of more than 220 ms
• Power-off the chip
DR Data
SGPB or CGPB
Bit Mask
DR Data
GGPB
Bit Mask
DR Data
SSE
AT91SAM7L128/64 Preliminary
171