C8051F501-IQ Silicon Laboratories Inc, C8051F501-IQ Datasheet - Page 254

• Manufacturer Part Number: C8051F501-IQ
• Description: IC 8051 MCU 64K FLASH 48-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F50xr

Specifications of C8051F501-IQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 48-QFP
• Mfg Application Notes: LIN Bootloader AppNote
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 40
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 32x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F500DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 32-ch x 12-bit
• Package: 48PQFP
• Device Core: 8051
• Family Name: C8051F50x
• Maximum Speed: 50 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1527 - KIT DEV FOR C8051F50X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1512

C8051F50x/F51x
25.2. SPI0 Master Mode Operation
A SPI master device initiates all data transfers on a SPI bus. SPI0 is placed in master mode by setting the
Master Enable flag (MSTEN, SPI0CN.6). Writing a byte of data to the SPI0 data register (SPI0DAT) when
in master mode writes to the transmit buffer. If the SPI shift register is empty, the byte in the transmit buffer
is moved to the shift register, and a data transfer begins. The SPI0 master immediately shifts out the data
serially on the MOSI line while providing the serial clock on SCK. The SPIF (SPI0CN.7) flag is set to logic
1 at the end of the transfer. If interrupts are enabled, an interrupt request is generated when the SPIF flag
is set. While the SPI0 master transfers data to a slave on the MOSI line, the addressed SPI slave device
simultaneously transfers the contents of its shift register to the SPI master on the MISO line in a full-duplex
operation. Therefore, the SPIF flag serves as both a transmit-complete and receive-data-ready flag. The
data byte received from the slave is transferred MSB-first into the master's shift register. When a byte is
fully shifted into the register, it is moved to the receive buffer where it can be read by the processor by
reading SPI0DAT.
When configured as a master, SPI0 can operate in one of three different modes: multi-master mode, 3-wire
single-master mode, and 4-wire single-master mode. The default, multi-master mode is active when
NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 1. In this mode, NSS is an input to the device, and
is used to disable the master SPI0 when another master is accessing the bus. When NSS is pulled low in
this mode, MSTEN (SPI0CN.6) and SPIEN (SPI0CN.0) are set to 0 to disable the SPI master device, and
a Mode Fault is generated (MODF, SPI0CN.5 = 1). Mode Fault will generate an interrupt if enabled. SPI0
must be manually re-enabled in software under these circumstances. In multi-master systems, devices will
typically default to being slave devices while they are not acting as the system master device. In multi-mas-
ter mode, slave devices can be addressed individually (if needed) using general-purpose I/O pins.
Figure 25.2 shows a connection diagram between two master devices in multiple-master mode.
3-wire single-master mode is active when NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 0. In this
mode, NSS is not used, and is not mapped to an external port pin through the crossbar. Any slave devices
that must be addressed in this mode should be selected using general-purpose I/O pins. Figure 25.3
shows a connection diagram between a master device in 3-wire master mode and a slave device.
4-wire single-master mode is active when NSSMD1 (SPI0CN.3) = 1. In this mode, NSS is configured as an
output pin, and can be used as a slave-select signal for a single SPI device. In this mode, the output value
of NSS is controlled (in software) with the bit NSSMD0 (SPI0CN.2). Additional slave devices can be
addressed using general-purpose I/O pins. Figure 25.4 shows a connection diagram for a master device in
4-wire master mode and two slave devices.
254
Rev. 1.2