C8051F501-IQ Silicon Laboratories Inc, C8051F501-IQ Datasheet - Page 76

• Manufacturer Part Number: C8051F501-IQ
• Description: IC 8051 MCU 64K FLASH 48-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F50xr

Specifications of C8051F501-IQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 48-QFP
• Mfg Application Notes: LIN Bootloader AppNote
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 40
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 32x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F500DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 32-ch x 12-bit
• Package: 48PQFP
• Device Core: 8051
• Family Name: C8051F50x
• Maximum Speed: 50 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1527 - KIT DEV FOR C8051F50X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1512

C8051F50x/F51x
Comparator outputs can be polled in software, used as an interrupt source, and/or routed to a Port pin.
When routed to a Port pin, Comparator outputs are available asynchronous or synchronous to the system
clock; the asynchronous output is available even in STOP mode (with no system clock active). When dis-
abled, the Comparator output (if assigned to a Port I/O pin via the Crossbar) defaults to the logic low state,
and the power supply to the comparator is turned off. See Section “20.3. Priority Crossbar Decoder” on
page 180 for details on configuring Comparator outputs via the digital Crossbar. Comparator inputs can be
externally driven from –0.25 V to (V
trical specifications are given in Table 5.12.
The Comparator response time may be configured in software via the CPTnMD registers (see SFR Defini-
tion 9.2). Selecting a longer response time reduces the Comparator supply current. See Table 5.12 on
page 51 for complete timing and supply current requirements.
Comparator hysteresis is software-programmable via its Comparator Control register CPTnCN.
The amount of negative hysteresis voltage is determined by the settings of the CPnHYN bits. As shown in
Figure 9.2, various levels of negative hysteresis can be programmed, or negative hysteresis can be dis-
abled. In a similar way, the amount of positive hysteresis is determined by the setting the CPnHYP bits.
Comparator interrupts can be generated on both rising-edge and falling-edge output transitions. (For Inter-
rupt enable and priority control, see “14. Interrupts” on page 117.) The CPnFIF flag is set to 1 upon a Com-
parator falling-edge, and the CPnRIF flag is set to 1 upon the Comparator rising-edge. Once set, these bits
remain set until cleared by software. The output state of the Comparator can be obtained at any time by
reading the CPnOUT bit. The Comparator is enabled by setting the CPnEN bit to 1, and is disabled by
clearing this bit to 0.
76
(Programmed with CPnHYP Bits)
Positive Hysteresis Voltage
INPUTS
OUTPUT
VIN+
VIN-
CIRCUIT CONFIGURATION
Positive Hysteresis
CPn-
VIN+
CPn+
VIN-
V
Disabled
OL
Figure 9.2. Comparator Hysteresis Plot
V
OH
+
_
CPn
DD
) + 0.25 V without damage or upset. The complete Comparator elec-
Positive Hysteresis
Maximum
OUT
Rev. 1.2
Negative Hysteresis
Disabled
Negative Hysteresis
(Programmed by CPnHYN Bits)
Maximum
Negative Hysteresis Voltage