MC56F8346MFVE Freescale Semiconductor, MC56F8346MFVE Datasheet - Page 37

• Manufacturer Part Number: MC56F8346MFVE
• Description: IC DSP 16BIT 60MHZ 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8346MFVE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 60MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 62
• Program Memory Size: 136KB (68K x 16)
• Program Memory Type: FLASH
• Ram Size: 6K x 16
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F83xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 60 MIPs
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 62
• Data Ram Size: 4 KB
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Interface Type: SCI, SPI, CAN
• Minimum Operating Temperature: - 40 C
• For Use With: MC56F8367EVME - EVAL BOARD FOR MC56F83X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor
Preliminary
TEMP_SENSE
Signal Name
(GPIOE8)
CAN_RX
CAN_TX
ANB0
ANB1
ANB2
ANB3
ANB4
ANB5
ANB6
ANB7
TC0
Table 2-2 Signal and Package Information for the 144 Pin LQFP
Pin No.
104
105
106
107
108
109
110
111
127
126
118
96
Schmitt
Schmitt
Schmitt
Output
Output
Output
Output
Open
Input/
Input/
Type
Drain
Input
Input
Input
enabled
enabled
During
Analog
Analog
Analog
Output
pull-up
Output
pull-up
56F8346 Technical Data, Rev. 15
Reset
Input,
Input,
State
Open
Drain
Input
Input
ANB0 - 3 — Analog inputs to ADC B, channel 0
ANB4 - 7 — Analog inputs to ADC B, channel 1
Temperature Sensor Diode — This signal connects to an on-chip
diode that can be connected to one of the ADC inputs and used to
monitor the temperature of the die. Must be bypassed with a
0.01μF capacitor.
FlexCAN Receive Data — This is the CAN input. This pin has an
internal pull-up resistor.
To deactivate the internal pull-up resistor, set the CAN bit in the
SIM_PUDR register.
FlexCAN Transmit Data — CAN output with internal pull-up
enable at reset.*
* Note: If a pin is configured as open drain output mode, internal
pull-up will automatically be disabled when it outputs low. Internal
pull-up will be enabled unless it has been manually disabled by
clearing the corresponding bit in the PUREN register of the GPIO
module, when it outputs high.
If a pin is configured as push-pull output mode, internal pull-up will
automatically be disabled, whether it outputs low or high.
TC0 — Timer C Channel 0
Port E GPIO — This GPIO pin can be programmed as an input or
output pin.
At reset, this pin defaults to timer functionality.
To deactivate the internal pull-up resistor, clear bit 8 of the
GPIOE_PUR register.
Signal Description
Signal Pins
37