C8051F120-GQ Silicon Laboratories Inc, C8051F120-GQ Datasheet - Page 260
![IC 8051 MCU FLASH 128K 100TQFP](/photos/12/21/122164/c8051f120-gq_sml.jpg)
C8051F120-GQ
Manufacturer Part Number
C8051F120-GQ
Description
IC 8051 MCU FLASH 128K 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F12xr
Specifications of C8051F120-GQ
Program Memory Type
FLASH
Program Memory Size
128KB (128K x 8)
Package / Case
100-TQFP, 100-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
100MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Ram Size
8.25K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F1x
Core
8051
Data Bus Width
8 bit
Data Ram Size
8.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
100 MHz
Number Of Programmable I/os
64
Number Of Timers
5
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F120DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 8-bit or 8-ch x 12-bit
On-chip Dac
2-ch x 12-bit
No. Of I/o's
64
Ram Memory Size
8448Byte
Cpu Speed
100MHz
No. Of Timers
5
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1285 - KIT DEV EMBEDDED MODEM336-1284 - KIT DEV EMBEDDED ETHERNET336-1224 - DEVKIT-F120/21/22/23/24/25/26/27
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1223
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F120-GQ
Manufacturer:
SiliconL
Quantity:
4 353
Company:
Part Number:
C8051F120-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F120-GQR
Manufacturer:
PEAK
Quantity:
5 000
Company:
Part Number:
C8051F120-GQR
Manufacturer:
SILICON
Quantity:
2
Company:
Part Number:
C8051F120-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F120-GQR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
C8051F120/1/2/3/4/5/6/7
C8051F130/1/2/3
Figure 19.2 shows a typical SMBus configuration. The SMBus0 interface will work at any voltage between
3.0 and 5.0 V and different devices on the bus may operate at different voltage levels. The bi-directional
SCL (serial clock) and SDA (serial data) lines must be connected to a positive power supply voltage
through a pullup resistor or similar circuit. Every device connected to the bus must have an open-drain or
open-collector output for both the SCL and SDA lines, so that both are pulled high when the bus is free.
The maximum number of devices on the bus is limited only by the requirement that the rise and fall times
on the bus will not exceed 300 ns and 1000 ns, respectively.
19.1. Supporting Documents
It is assumed the reader is familiar with or has access to the following supporting documents:
19.2. SMBus Protocol
Two types of data transfers are possible: data transfers from a master transmitter to an addressed slave
receiver (WRITE), and data transfers from an addressed slave transmitter to a master receiver (READ).
The master device initiates both types of data transfers and provides the serial clock pulses on SCL. Note:
multiple master devices on the same bus are supported. If two or more masters attempt to initiate a data
transfer simultaneously, an arbitration scheme is employed with a single master always winning the arbitra-
tion. Note that it is not necessary to specify one device as the master in a system; any device who trans-
mits a START and a slave address becomes the master for that transfer.
A typical SMBus transaction consists of a START condition followed by an address byte (Bits7–1: 7-bit
slave address; Bit0: R/W direction bit), one or more bytes of data, and a STOP condition. Each byte that is
received (by a master or slave) must be acknowledged (ACK) with a low SDA during a high SCL (see
Figure 19.3). If the receiving device does not ACK, the transmitting device will read a “not acknowledge”
(NACK), which is a high SDA during a high SCL.
The direction bit (R/W) occupies the least-significant bit position of the address. The direction bit is set to
logic 1 to indicate a "READ" operation and cleared to logic 0 to indicate a "WRITE" operation.
260
VDD = 5V
1. The I2C-bus and how to use it (including specifications), Philips Semiconductor.
2. The I2C-Bus Specification -- Version 2.0, Philips Semiconductor.
3. System Management Bus Specification -- Version 1.1, SBS Implementers Forum.
Figure 19.2. Typical SMBus Configuration
VDD = 3V
Master
Device
Rev. 1.4
Device 1
VDD = 5V
Slave
VDD = 3V
Device 2
Slave
SDA
SCL