DSPIC33FJ12GP202-I/SS Microchip Technology, DSPIC33FJ12GP202-I/SS Datasheet - Page 134

• Manufacturer Part Number: DSPIC33FJ12GP202-I/SS
• Description: IC DSPIC MCU/DSP 12K 28SSOP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ12GP202-I/SS

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 12KB (12K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: I2C, JTAG, SPI, UART
• No. Of I/o's: 21
• Flash Memory Size: 12KB
• Supply Voltage Range: 3V To 3.6V
• Package: 28SSOP
• Device Core: dsPIC
• Family Name: dsPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC33FJ12GP201/202
13.1
Configure the Output Compare modes by setting the
appropriate Output Compare Mode (OCM<2:0>) bits in
the Output Compare Control (OCxCON<2:0>) register.
Table 13-1 lists the different bit settings for the Output
TABLE 13-1:
FIGURE 13-2:
DS70264C-page 132
OCM<2:0>
Continuous Pulse Mode
000
001
010
011
100
101
110
111
Active-High One-Shot
Active-Low One-Shot
(OCM = 110 or 111)
Delayed One-Shot
Output Compare Modes
(OCM = 011)
(OCM = 100)
Toggle Mode
(OCM = 101)
(OCM = 001)
(OCM = 010)
PWM Mode
Module Disabled
Active-Low One-Shot
Active-High One-Shot
Toggle Mode
Delayed One-Shot
Continuous Pulse mode
PWM mode without fault
protection
PWM mode with fault protection 0, if OCxR is zero
OUTPUT COMPARE MODES
TMRy
OUTPUT COMPARE OPERATION
OCxRS
OCxR
Mode
Output Compare
Mode enabled
Controlled by GPIO register
Current output is maintained
0, if OCxR is zero
1, if OCxR is non-zero
1, if OCxR is non-zero
Preliminary
OCx Pin Initial State
Timer is reset on
period match
0
1
0
0
Compare modes. Figure 13-2 illustrates the output
compare operation for various modes. The user
application must disable the associated timer when
writing to the output compare control registers to avoid
malfunctions.
OCx Rising edge
OCx Falling edge
OCx Rising and Falling edge
OCx Falling edge
OCx Falling edge
No interrupt
OCFA Falling edge for OC1 to OC4
OCx Interrupt Generation
© 2008 Microchip Technology Inc.
—