ATTINY861-20SU Atmel, ATTINY861-20SU Datasheet - Page 45

• Manufacturer Part Number: ATTINY861-20SU
• Description: IC MCU AVR 8K FLASH 20MHZ 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY861-20SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: USI
• Total Internal Ram Size: 512Byte
• # I/os (max): 16
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 11-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: SOIC
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRMC320
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.3.1
8.3.1.1
8.3.1.2
2588E–AVR–08/10
Timed Sequences for Changing the Configuration of the Watchdog Timer
Safety Level 1
Safety Level 2
The Wathdog Timer can also be configured to generate an interrupt instead of a reset. This can
be very helpful when using the Watchdog to wake-up from Power-down.
To prevent unintentional disabling of the Watchdog or unintentional change of time-out period,
two different safety levels are selected by the fuse WDTON as shown in
“Timed Sequences for Changing the Configuration of the Watchdog Timer” on page 45
details.
Table 8-1.
Figure 8-7.
The sequence for changing configuration differs slightly between the two safety levels. Separate
procedures are described for each level.
In this mode, the Watchdog Timer is initially disabled, but can be enabled by writing the WDE bit
to one without any restriction. A timed sequence is needed when disabling an enabled Watch-
dog Timer. To disable an enabled Watchdog Timer, the following procedure must be followed:
In this mode, the Watchdog Timer is always enabled, and the WDE bit will always read as one. A
timed sequence is needed when changing the Watchdog Time-out period. To change the
Watchdog Time-out, the following procedure must be followed:
WDTON
Unprogrammed
Programmed
1. In the same operation, write a logic one to WDCE and WDE. A logic one must be writ-
2. Within the next four clock cycles, in the same operation, write the WDE and WDP bits
ten to WDE regardless of the previous value of the WDE bit.
as desired, but with the WDCE bit cleared.
WDT Configuration as a Function of the Fuse Settings of WDTON
Watchdog Timer
Safety
Level
WATCHDOG
1
2
OSCILLATOR
RESET
128 kHz
WDP0
WDP1
WDP2
WDP3
WDE
WDT Initial
State
Disabled
Enabled
How to Disable the
WDT
Timed sequence
Always enabled
MCU RESET
PRESCALER
WATCHDOG
How to Change Time-
out
No limitations
Timed sequence
Table 8-1
Refer to
for
45