ATMEGA169P-16MCH Atmel, ATMEGA169P-16MCH Datasheet - Page 34

• Manufacturer Part Number: ATMEGA169P-16MCH
• Description: MCU AVR 16KB FLASH 16MHZ 64-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169P-16MCH

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.6
8018P–AVR–08/10
Low-frequency Crystal Oscillator
The CKSEL0 Fuse together with the SUT1..0 Fuses select the start-up times as shown in
8-6.
Table 8-6.
Notes:
The Low-frequency Crystal Oscillator is optimized for use with a 32.768 kHz watch crystal.
When selecting crystals, load capacitance and crystal’s Equivalent Series Resistance, ESR
must be taken into consideration. Both values are specified by the crystal vendor. ATmega169P
oscillator is optimized for very low power consumption, and thus when selecting crystals, see
Table 8-7
Table 8-7.
Note:
The Low-frequency Crystal Oscillator provides an internal load capacitance, see
page 35
CKSEL0
0
0
0
0
1
1
1
1
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
1. Maximum ESR is typical value based on characterization
at each TOSC pin.
for maximum ESR recommendations on 9 pF and 6.5 pF crystals.
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
SUT1:0
Start-up Times for the Crystal Oscillator Clock Selection
Maximum ESR Recommendation for 32.768 kHz Watch Crystal
00
01
10
11
00
01
10
11
Crystal CL (pF)
6.5
9
Start-up Time from
Power-down and
Power-save
258 CK
258 CK
1K CK
1K CK
1K CK
16K CK
16K CK
16K CK
(2)
(2)
(2)
(1)
(1)
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
14CK + 4.1 ms
14CK + 65 ms
14CK + 65 ms
14CK + 65 ms
(V
from Reset
CC
14CK
14CK
= 5.0V)
Max ESR [kΩ]
ATmega169P
Recommended Usage
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Crystal Oscillator, BOD
enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator, slowly
rising power
60
35
(1)
Table 8-8 on
Table
34