PIC18F27J13-I/ML Microchip Technology, PIC18F27J13-I/ML Datasheet - Page 284

• Manufacturer Part Number: PIC18F27J13-I/ML
• Description: IC PIC MCU 128KB FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J13-I/ML

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Digital Ic Case Style: QFN
• Supply Voltage Range: 1.8V To 5.5V
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 19
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DM164128, DM180021, DM183026-2, DV164131, MA180030, DM183022, DM183032, DV164136, MA180024
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180030 - BOARD DEMO PIC18F47J13 FS USBMA180029 - BOARD DEMO PIC18F47J53 FS USB
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18(L)F2X/4XK22
16.4.1.5
1.
2.
3.
FIGURE 16-10:
FIGURE 16-11:
DS41412D-page 284
TXx/CKx pin
(SCKP = 1)
TXx/CKx pin
(SCKP = 0)
TRMT bit
RXx/DTx
pin
Write to
TXREGx Reg
TXxIF bit
(Interrupt Flag)
TXEN bit
Note:
Initialize the SPBRGHx, SPBRGx register pair
and the BRGH and BRG16 bits to achieve the
desired baud rate (see
Baud Rate Generator
Set the RXx/DTx and TXx/CKx TRIS controls to
‘1’.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC. Set the
TRIS bits corresponding to the RXx/DTx and
TXx/CKx I/O pins.
‘1’
Synchronous Master Transmission
Setup:
Sync Master mode, SPBRGx = 0, continuous transmission of two 8-bit words.
Write Word 1
TXREGx reg
RXx/DTx pin
TXx/CKx pin
TRMT bit
TXxIF bit
TXEN bit
Write to
SYNCHRONOUS TRANSMISSION
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
bit 0
Section 16.3 “EUSART
(BRG)”).
Write Word 2
bit 1
Word 1
bit 0
bit 2
Preliminary
bit 1
bit 7
4.
5.
6.
7.
8.
9.
Disable Receive mode by clearing bits SREN
and CREN.
Enable Transmit mode by setting the TXEN bit.
If 9-bit transmission is desired, set the TX9 bit.
If interrupts are desired, set the TXxIE, GIE/
GIEH and PEIE/GIEL interrupt enable bits.
If 9-bit transmission is selected, the ninth bit
should be loaded in the TX9D bit.
Start transmission by loading data to the
TXREGx register.
bit 2
bit 0
Word 2
bit 1
bit 6
 2010 Microchip Technology Inc.
bit 7
bit 7
‘1’