PIC18F27J13-I/ML Microchip Technology, PIC18F27J13-I/ML Datasheet - Page 60

• Manufacturer Part Number: PIC18F27J13-I/ML
• Description: IC PIC MCU 128KB FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J13-I/ML

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Digital Ic Case Style: QFN
• Supply Voltage Range: 1.8V To 5.5V
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 19
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DM164128, DM180021, DM183026-2, DV164131, MA180030, DM183022, DM183032, DV164136, MA180024
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180030 - BOARD DEMO PIC18F47J13 FS USBMA180029 - BOARD DEMO PIC18F47J53 FS USB
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18(L)F2X/4XK22
REGISTER 4-1:
DS41412D-page 60
bit 7
Legend:
R = Readable bit
‘1’ = Bit is set
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
x = Bit is unknown
Note 1: Brown-out Reset is indicated when BOR is ‘0’ and POR is ‘1’ (assuming that both POR and BOR were set
R/W-0/0
IPEN
2:
3:
2: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent
When CONFIG2L[2:1] = 01, then the SBOREN Reset state is ‘1’; otherwise, it is ‘0’.
The actual Reset value of POR is determined by the type of device Reset. See the notes following this
register and
See
to ‘1’ by firmware immediately after POR).
Power-on Resets may be detected.
Table
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
SBOREN: BOR Software Enable bit
If BOREN<1:0> = 01:
1 = BOR is enabled
0 = BOR is disabled
If BOREN<1:0> = 00, 10 or 11:
Bit is disabled and read as ‘0’.
Unimplemented: Read as ‘0’
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware or Power-on Reset)
0 = The RESET instruction was executed causing a device Reset (must be set in firmware after a
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
POR: Power-on Reset Status bit
1 = No Power-on Reset occurred
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set by firmware after a POR or Brown-out Reset occurs)
SBOREN
R/W-q/u
code-executed Reset occurs)
4-1.
RCON: RESET CONTROL REGISTER
Section 4.6 “Reset State of Registers”
(1)
W = Writable bit
‘0’ = Bit is cleared
u = unchanged
U-0
—
R/W-1/q
(2)
(3)
Preliminary
RI
(1)
U = Unimplemented bit, read as ‘0’
-n/n = Value at POR and BOR/Value at all other Resets
q = depends on condition
R-1/q
TO
for additional information.
R-1/q
PD
 2010 Microchip Technology Inc.
R/W-q/u
POR
(2)
R/W-0/q
BOR
bit 0