PIC18LF2420-I/SP Microchip Technology, PIC18LF2420-I/SP Datasheet - Page 189

• Manufacturer Part Number: PIC18LF2420-I/SP
• Description: IC MCU FLASH 8KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF2420-I/SP

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 10-chx10-bit
• Number Of Timers: 4
• Core: PIC
• Processor Series: PIC18LF
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 768 B
• Data Rom Size: 256 B
• Mounting Style: Through Hole
• Height: 3.3 mm
• Length: 34.67 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 7.24 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

17.4.7
In I
reload value is placed in the lower 7 bits of the
SSPADD register (Figure 17-17). When a write occurs
to SSPBUF, the Baud Rate Generator will automatically
begin counting. The BRG counts down to 0 and stops
until another reload has taken place. The BRG count is
decremented twice per instruction cycle (T
Q2 and Q4 clocks. In I
reloaded automatically.
FIGURE 17-17:
TABLE 17-3:
© 2008 Microchip Technology Inc.
Note 1:
2
C Master mode, the Baud Rate Generator (BRG)
10 MHz
10 MHz
10 MHz
4 MHz
4 MHz
4 MHz
1 MHz
1 MHz
1 MHz
The I
100 kHz) in all details, but may be used with care where higher rates are required by the application.
BAUD RATE
F
CY
2
C interface does not conform to the 400 kHz I
I
2
C™ CLOCK RATE W/BRG
BAUD RATE GENERATOR BLOCK DIAGRAM
2
C Master mode, the BRG is
SSPM<3:0>
SCL
20 MHz
20 MHz
20 MHz
F
8 MHz
8 MHz
8 MHz
2 MHz
2 MHz
2 MHz
CY
SSPM<3:0>
CY
* 2
PIC18F2420/2520/4420/4520
) on the
Reload
Control
CLKO
Reload
Once the given operation is complete (i.e., transmis-
sion of the last data bit is followed by ACK), the internal
clock will automatically stop counting and the SCL pin
will remain in its last state.
Table 17-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
2
BRG Down Counter
C specification (which applies to rates greater than
SSPADD<6:0>
BRG Value
0Ch
1Fh
18h
63h
09h
27h
02h
09h
00h
F
OSC
(2 Rollovers of BRG)
/4
400 kHz
400 kHz
333 kHz
312.5 kHz
1 MHz
DS39631E-page 187
100 kHz
308 kHz
100 kHz
100 kHz
F
SCL
(1)
(1)
(1)
(1)