ATXMEGA16A4-CU Atmel, ATXMEGA16A4-CU Datasheet - Page 199

• Manufacturer Part Number: ATXMEGA16A4-CU
• Description: MCU AVR 16+4KB FLASH 49VFBGA
• Manufacturer: Atmel
• Series: AVR® XMEGAr

Specifications of ATXMEGA16A4-CU

• Core Processor: AVR
• Core Size: 8/16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.6 V ~ 3.6 V
• Data Converters: A/D 12x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 49-VFBGA
• Processor Series: ATXMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 2 KB
• Interface Type: I2C/SPI/USART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 5
• Operating Supply Voltage: 1.6 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 12-bit
• On-chip Dac: 2-ch x 12-bit
• For Use With: ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18.3.2
18.3.3
SYNCCTRL - Synchronisation Control/Status Register
INTCTRL - Interrupt Control Register
• Bit 0 - ENABLE: RTC Enable
Setting this bit enables the RTC. The synchronization time between the RTC and the System
Clock domains is one half RTC clock cycle from writing the register and until this has effect in
RTC clock domain, i.e until the RTC starts.
For the RTC to start running the PER Register must also be set to a different value that zero.
• Bits 7:5 - Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bit 4- SYNCCNT: Enable Synchronization of the CNT register
Setting this bit will start synchronization of CNT register from the RTC clock to the System Clock
domain. The bit is automatically cleared when synchronization is done.
• Bits 3:1 - Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bit 0 - SYNCBUSY: RTC Synchronization Busy Flag
This flag is set when the CTRL or CNT registers are busy synchronizing from the System Clock
to the RTC clock domain. The CTRL register synchronization is triggered when it is written. The
CNT register are synchronized when the most significant byte of the register is written.
• Bits 7:4 - Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bits 3:2 - COMPINTLVL[1:0]: RTC Compare Match Interrupt Enable
These bits enable the RTC Compare Match Interrupt and select the interrupt level as described
in
enabled interrupt will trigger when the COMPIF in the INTFLAGS register is set.
Bit
+0x01
Read/Write
Reset Value
Bit
+0x02
Read/Write
Reset Value
Section 12. ”Interrupts and Programmable Multi-level Interrupt Controller” on page
7
-
R
0
7
-
R
0
6
-
R
0
6
-
R
0
5
-
R
0
5
-
R
0
SYNCCNT
R/W
4
0
4
-
R
0
COMPINTLVL[1:0]
R/W
3
3
-
R
0
0
R/W
2
2
-
R
0
0
R/W
1
1
-
R
0
0
OCINTLVL[1:0]
SYNCBUSY
R/W
R/W
0
0
0
0
SYNCCTRL
INTCTRL
123. The