DSPIC30F5016-20E/PT Microchip Technology, DSPIC30F5016-20E/PT Datasheet - Page 119
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
DSPIC30F5016-20E/PT
Manufacturer Part Number
DSPIC30F5016-20E/PT
Description
IC DSPIC MCU/DSP 66K 80TQFP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20IP.pdf
(26 pages)
3.DSPIC30F5016-30IPT.pdf
(230 pages)
4.DSPIC30F5016-30IPT.pdf
(14 pages)
5.DSPIC30F5016-30IPT.pdf
(6 pages)
6.DSPIC30F5016-30IPT.pdf
(18 pages)
Specifications of DSPIC30F5016-20E/PT
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
68
Program Memory Size
66KB (22K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
80-TFQFP
For Use With
AC164320 - MODULE SKT MPLAB PM3 80TQFPAC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F5016-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
18.2
18.2.1
The UART module is enabled by setting the UARTEN
bit in the UxMODE register (where x = 1). Once
enabled, the UxTX and UxRX pins are configured as an
output and an input respectively, overriding the TRIS
and LATCH register bit settings for the corresponding
I/O port pins. The UxTX pin is at logic ‘1’ when no
transmission is taking place.
18.2.2
The UART module is disabled by clearing the
UARTEN bit in the UxMODE register. This is the
default state after any Reset. If the UART is disabled,
all I/O pins operate as port pins under the control of
the latch and TRIS bits of the corresponding port pins.
Disabling the UART module resets the buffers to
empty states. Any data characters in the buffers are
lost, and the baud rate counter is reset.
All error and status flags associated with the UART
module are reset when the module is disabled. The
URXDA, OERR, FERR, PERR, UTXEN, UTXBRK and
UTXBF bits are cleared, whereas RIDLE and TRMT
are set. Other control bits, including ADDEN,
URXISEL<1:0>, UTXISEL, as well as the UxMODE
and UxBRG registers, are not affected.
Clearing the UARTEN bit while the UART is active will
abort all pending transmissions and receptions and
reset the module as defined above. Re-enabling the
UART will restart the UART in the same configuration.
18.2.3
Control bits, PDSEL<1:0>, in the UxMODE register are
used to select the data length and parity used in the
transmission. The data length may either be 8 bits with
even, odd or no parity, or 9 bits with no parity.
The STSEL bit determines whether one or two Stop bits
will be used during data transmission.
The default (Power-on) setting of the UART is 8 bits, no
parity, 1 Stop bit (typically represented as 8, N, 1).
© 2008 Microchip Technology Inc.
Enabling and Setting Up UART
ENABLING THE UART
DISABLING THE UART
SETTING UP DATA, PARITY AND
STOP BIT SELECTIONS
18.3
18.3.1
The following steps must be performed in order to
transmit 8-bit data:
1.
2.
3.
4.
5.
18.3.2
The sequence of steps involved in the transmission of
9-bit data is similar to 8-bit transmission, except that a
16-bit data word (of which the upper 7 bits are always
clear) must be written to the UxTXREG register.
18.3.3
The transmit buffer is 9 bits wide and 4 characters
deep. Including the Transmit Shift register (UxTSR),
the user effectively has a 5-deep FIFO (First-In,
First-Out) buffer. The UTXBF Status bit (UxSTA<9>)
indicates whether the transmit buffer is full.
If a user attempts to write to a full buffer, the new data
will not be accepted into the FIFO, and no data shift
will occur within the buffer. This enables recovery from
a buffer overrun condition.
The FIFO is reset during any device Reset, but is not
affected when the device enters or wakes up from a
Power-Saving mode.
dsPIC30F5015/5016
Set up the UART:
First, the data length, parity and number of Stop
bits must be selected. Then, the Transmit and
Receive Interrupt enable and priority bits are
setup in the UxMODE and UxSTA registers.
Also, the appropriate baud rate value must be
written to the UxBRG register.
Enable the UART by setting the UARTEN bit
(UxMODE<15>).
Set the UTXEN bit (UxSTA<10>), thereby
enabling a transmission.
Write the byte to be transmitted to the lower byte
of UxTXREG. The value will be transferred to the
Transmit Shift register (UxTSR) immediately
and the serial bit stream will start shifting out
during the next rising edge of the baud clock.
Alternatively, the data byte may be written while
UTXEN = 0, following which, the user may set
UTXEN. This will cause the serial bit stream to
begin immediately because the baud clock will
start from a cleared state.
A Transmit interrupt will be generated depend-
ing on the value of the interrupt control bit
UTXISEL (UxSTA<15>).
Note:
Transmitting Data
TRANSMITTING IN 8-BIT DATA
MODE
TRANSMITTING IN 9-BIT DATA
MODE
TRANSMIT BUFFER (U
The UTXEN bit must be set after the
UARTEN bit is set to enable UART
transmissions.
DS70149D-page 119
X
TXB)