DSPIC30F5016-20E/PT Microchip Technology, DSPIC30F5016-20E/PT Datasheet - Page 140
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
DSPIC30F5016-20E/PT
Manufacturer Part Number
DSPIC30F5016-20E/PT
Description
IC DSPIC MCU/DSP 66K 80TQFP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20IP.pdf
(26 pages)
3.DSPIC30F5016-30IPT.pdf
(230 pages)
4.DSPIC30F5016-30IPT.pdf
(14 pages)
5.DSPIC30F5016-30IPT.pdf
(6 pages)
6.DSPIC30F5016-30IPT.pdf
(18 pages)
Specifications of DSPIC30F5016-20E/PT
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
68
Program Memory Size
66KB (22K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
80-TFQFP
For Use With
AC164320 - MODULE SKT MPLAB PM3 80TQFPAC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F5016-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
dsPIC30F5015/5016
20.2.6
The LPRC oscillator is a component of the Watchdog
Timer (WDT) and oscillates at a nominal frequency of
512 kHz. The LPRC oscillator is the clock source for
the Power-up Timer (PWRT) circuit, WDT and clock
monitor circuits. It may also be used to provide a low
frequency clock source option for applications where
power consumption is critical, and timing accuracy is
not required.
The LPRC oscillator is always enabled at a Power-on
Reset, because it is the clock source for the PWRT.
After the PWRT expires, the LPRC oscillator will remain
ON if one of the following is TRUE:
• The Fail-Safe Clock Monitor is enabled
• The WDT is enabled
• The LPRC oscillator is selected as the system
If one of the above conditions is not true, the LPRC will
shut-off after the PWRT expires.
20.2.7
The Fail-Safe Clock Monitor (FSCM) allows the device
to continue to operate even in the event of an oscillator
failure. The FSCM function is enabled by appropriately
programming the FCKSM Configuration bits (Clock
Switch and Monitor Selection bits) in the FOSC
Configuration register. If the FSCM function is
enabled, the LPRC Internal oscillator will run at all
times (except during Sleep mode) and will not be
subject to control by the SWDTEN bit.
In the event of an oscillator failure, the FSCM will
generate a clock failure trap event and will switch the
system clock over to the FRC oscillator. The user will
then have the option to either attempt to restart the
oscillator or execute a controlled shutdown. The user
may decide to treat the trap as a warm Reset by simply
loading the Reset address into the oscillator fail trap
vector. In this event, the CF (Clock Fail) Status bit
(OSCCON<3>) is also set whenever a clock failure is
recognized.
In the event of a clock failure, the WDT is unaffected
and continues to run on the LPRC clock.
If the oscillator has a very slow start-up time coming
out of POR, BOR or Sleep, it is possible that the
PWRT timer will expire before the oscillator has
started. In such cases, the FSCM will be activated and
the FSCM will initiate a clock failure trap, and the
DS70149D-page 140
clock via the COSC<2:0> control bits in the
OSCCON register
Note 1: OSC2 pin function is determined by the
2: Note that OSC1 pin cannot be used as an
LOW-POWER RC OSCILLATOR
(LPRC)
FAIL-SAFE CLOCK MONITOR
Primary
(FPR<4:0>).
I/O pin, even if the secondary oscillator or
an internal clock source is selected at all
times.
Oscillator
mode
selection
COSC<2:0> bits are loaded with FRC oscillator selec-
tion. This will effectively shut-off the original oscillator
that was trying to start.
The user may detect this situation and restart the
oscillator in the clock fail trap, ISR.
Upon a clock failure detection, the FSCM module will
initiate a clock switch to the FRC oscillator as follows:
1.
2.
3.
For the purpose of clock switching, the clock sources
are sectioned into four groups:
1.
2.
3.
4.
The user can switch between these functional groups,
but cannot switch between options within a group. If the
primary group is selected, then the choice within the
group is always determined by the FPR<4:0>
Configuration bits.
The OSCCON register holds the control and Status bits
related to clock switching.
• COSC<2:0>: Read-only Status bits always reflect
• NOSC<2:0>: Control bits which are written to
• LOCK: The LOCK Status bit indicates a PLL lock.
• CF: Read-only Status bit indicating if a clock fail
• OSWEN: Control bit changes from a ‘0’ to a ‘1’
If Configuration bits FCKSM<1:0> = 1x, then the clock
switching and Fail-Safe Clock Monitor functions are
disabled. This is the default Configuration bit setting.
If clock switching is disabled, then the FOS<2:0> and
FPR<4:0> bits directly control the oscillator selection
and the COSC<2:0> bits do not control the clock
selection. However, these bits will reflect the clock
source selection.
the current oscillator group in effect.
indicate the new oscillator group of choice.
- On POR and BOR, COSC<2:0> and
detect has occurred.
when a clock transition sequence is initiated.
Clearing the OSWEN control bit will abort a clock
transition in progress (used for hang-up
situations).
Note:
The COSC bits (OSCCON<14:12>) are loaded
with the FRC oscillator selection value.
CF bit is set (OSCCON<3>).
OSWEN control bit (OSCCON<0>) is cleared.
Primary
Secondary
Internal FRC
Internal LPRC
NOSC<2:0> are both loaded with the
Configuration bit values FOS<2:0>.
The application should not attempt to
switch to a clock of frequency lower than
100 KHz when the Fail-Safe Clock Monitor
is enabled. If clock switching is performed,
the device may generate an oscillator fail
trap and switch to the Fast RC oscillator.
© 2008 Microchip Technology Inc.