PIC18F2685-E/SO Microchip Technology, PIC18F2685-E/SO Datasheet - Page 25

• Manufacturer Part Number: PIC18F2685-E/SO
• Description: IC PIC MCU FLASH 48KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2685-E/SO

• Core Size: 8-Bit
• Program Memory Size: 96KB (48K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 28
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3328Byte
• Cpu Speed: 40MHz
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.25 KB
• Interface Type: EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 28
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

2.0
2.1
PIC18F2682/2685/4682/4685 devices can be operated
in ten different oscillator modes. The user can program
the Configuration bits, FOSC3:FOSC0, in Configuration
Register 1H to select one of these ten modes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. ECIO
2.2
In XT, LP, HS or HSPLL Oscillator modes, a crystal or
ceramic resonator is connected to the OSC1 and
OSC2 pins to establish oscillation. Figure 2-1 shows
the pin connections.
The oscillator design requires the use of a parallel cut
crystal.
© 2009 Microchip Technology Inc.
Note:
LP
XT
HS
HSPLL High-Speed Crystal/Resonator
RC
RCIO
INTIO1 Internal Oscillator with F
INTIO2 Internal Oscillator with I/O on RA6
EC
OSCILLATOR
CONFIGURATIONS
Oscillator Types
Crystal Oscillator/Ceramic
Resonators
Use of a series cut crystal may give a
frequency out of the crystal manufacturer’s
specifications.
Low-Power Crystal
Crystal/Resonator
High-Speed Crystal/Resonator
with PLL enabled
External Resistor/Capacitor with
F
External Resistor/Capacitor with I/O
on RA6
on RA6 and I/O on RA7
and RA7
External Clock with F
External Clock with I/O on RA6
OSC
/4 output on RA6
OSC
OSC
/4 output
/4 output
PIC18F2682/2685/4682/4685
FIGURE 2-1:
TABLE 2-1:
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes on page 26 for additional information.
Note 1:See Table 2-1 and Table 2-2 for initial values of
DD
Note:
Mode
HS
XT
and temperature range for the application.
C1
C2
2: A series resistor (R
3: R
455 kHz
2.0 MHz
(1)
(1)
Typical Capacitor Values Used:
C1 and C2.
strip cut crystals.
When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any V
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of R
F
16.0 MHz
varies with the oscillator mode chosen.
XTAL
R
455 kHz
2.0 MHz
4.0 MHz
8.0 MHz
S
Freq
(2)
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC2
OSC1
16.0 MHz
CRYSTAL/CERAMIC
RESONATOR OPERATION
(XT, LP, HS OR HSPLL
CONFIGURATION)
S
) may be required for AT
OSC1
56 pF
47 pF
33 pF
27 pF
22 pF
R
F
(3)
PIC18FXXXX
4.0 MHz
8.0 MHz
DS39761C-page 25
S
is 330Ω.
Sleep
OSC2
56 pF
47 pF
33 pF
27 pF
22 pF
To
Internal
Logic
DD
for