ATXMEGA128D3-AU Atmel, ATXMEGA128D3-AU Datasheet - Page 97

• Manufacturer Part Number: ATXMEGA128D3-AU
• Description: MCU AVR 128K FLASH 3.6V 64TQFP
• Manufacturer: Atmel
• Series: AVR® XMEGAr

Specifications of ATXMEGA128D3-AU

• Core Processor: AVR
• Core Size: 8/16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.6 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: XMEGA
• Core: AVR
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 8 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Operating Supply Voltage: 2.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8134I–AVR–12/10
Table 33-2.
11. PWM is not restarted properly after a fault in cycle-by-cycle mode
12. BOD will be enabled after any reset
13. EEPROM page buffer always written when NVM DATA0 is written
14. Pending full asynchronous pin change interrupts will not wake the device
15. Pin configuration does not affect Analog Comparator output
Problem fix/Workaround
When the AWeX fault restore mode is set to cycle-by-cycle, the waveform output will not
return to normal operation at first update after fault condition is no longer present.
Problem fix/Workaround
Do a write to any AWeX I/O register to re-enable the output.
If any reset source goes active, the BOD will be enabled and keep the device in reset if the
VCC voltage is below the programmed BOD level. During Power-On Reset, reset will not be
released until VCC is above the programmed BOD level even if the BOD is disabled.
Problem fix/Workaround
Do not set the BOD level higher than VCC even if the BOD is not used.
If the EEPROM is memory mapped, writing to NVM DATA0 will corrupt data in the EEPROM
page buffer.
Problem fix/Workaround
Before writing to NVM DATA0, for example when doing software CRC or flash page buffer
write, check if EEPROM page buffer active loading flag (EELOAD) is set. Do not write NVM
DATA0 when EELOAD is set.
Any full asynchronous pin-change Interrupt from pin 2, on any port, that is pending when the
sleep instruction is executed, will be ignored until the device is woken from another source
or the source triggers again. This applies when entering all sleep modes where the System
Clock is stopped.
Problem fix/Workaround
None.
The Output/Pull and inverted pin configuration does not affect the Analog Comparator
output.
Problem fix/Workaround
None for Output/Pull configuration.
For inverted I/O, configure the Analog Comparator to give an inverted result (i.e. connect
positive input to the negative AC input and vice versa), or use and external inverter to
change polarity of Analog Comparator output.
PGM
0
0
1
1
Configure PWM and CWCM according to this table:
CWCM
0
1
0
1
Description
PGM and CWCM disabled
PGM enabled
PGM and CWCM enabled
PGM enabled
XMEGA D3
97