AT91SAM7X512-AU Atmel, AT91SAM7X512-AU Datasheet - Page 404

• Manufacturer Part Number: AT91SAM7X512-AU
• Description: MCU ARM 512K HS FLASH 100-LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X512-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 128 KB
• Interface Type: CAN, SPI, SSC, TWI, USART, USB
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7X-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• No. Of I/o's: 62
• Ram Memory Size: 128KB
• Cpu Speed: 55MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 4
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7X-EK - KIT EVAL FOR AT91SAM7X256/128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

32.5.12
32.5.13
404
AT91SAM7X512/256/128 Preliminary
External Event/Trigger Conditions
Output Controller
An external event can be programmed to be detected on one of the clock sources (XC0, XC1,
XC2) or TIOB. The external event selected can then be used as a trigger.
The EEVT parameter in TC_CMR selects the external trigger. The EEVTEDG parameter defines
the trigger edge for each of the possible external triggers (rising, falling or both). If EEVTEDG is
cleared (none), no external event is defined.
If TIOB is defined as an external event signal (EEVT = 0), TIOB is no longer used as an output
and the compare register B is not used to generate waveforms and subsequently no IRQs. In
this case the TC channel can only generate a waveform on TIOA.
When an external event is defined, it can be used as a trigger by setting bit ENETRG in
TC_CMR.
As in Capture Mode, the SYNC signal and the software trigger are also available as triggers. RC
Compare can also be used as a trigger depending on the parameter WAVSEL.
The output controller defines the output level changes on TIOA and TIOB following an event.
TIOB control is used only if TIOB is defined as output (not as an external event).
The following events control TIOA and TIOB: software trigger, external event and RC compare.
RA compare controls TIOA and RB compare controls TIOB. Each of these events can be pro-
grammed to set, clear or toggle the output as defined in the corresponding parameter in
TC_CMR.
6120H–ATARM–17-Feb-09