P89LPC9321FA,529 NXP Semiconductors, P89LPC9321FA,529 Datasheet - Page 22

• Manufacturer Part Number: P89LPC9321FA,529
• Description: IC 80C51 MCU FLASH 8K 28-PLCC
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC9321FA,529

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-PLCC
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Eeprom Size: 512 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-1758 - BOARD EVAL FOR LPC93X MCU FAMILY
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935287628529

NXP Semiconductors
P89LPC9321
Product data sheet
7.5 Clock output
7.6 On-chip RC oscillator option
7.7 Watchdog oscillator option
7.8 External clock input option
7.9 Clock sources switch on the fly
The P89LPC9321 supports a user-selectable clock output function on the
XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs if
another clock source has been selected (on-chip RC oscillator, watchdog oscillator,
external clock input on XTAL1) and if the RTC and WDT are not using the crystal oscillator
as their clock source. This allows external devices to synchronize to the P89LPC9321.
This output is enabled by the ENCLK bit in the TRIM register.
The frequency of this clock output is
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
The P89LPC9321 has a 6-bit TRIM register that can be used to tune the frequency of the
RC oscillator. During reset, the TRIM value is initialized to a factory preprogrammed value
to adjust the oscillator frequency to 7.373 MHz ± 1 % at room temperature. End-user
applications can write to the TRIM register to adjust the on-chip RC oscillator to other
frequencies. When the clock doubler option is enabled (UCFG2.7 = 1), the output
frequency is 14.746 MHz. If CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can
be set to logic 1 to reduce power consumption. On reset, CLKLP is logic 0 allowing
highest performance access. This bit can then be set in software if CCLK is running at
8 MHz or slower. When clock doubler option is enabled, BOE1 bit (UCFG1.5) and BOE0
bit (UCFG1.3) are required to hold the device in reset at power-up until V
its specified level.
The watchdog has a separate oscillator which has a frequency of 400 kHz, calibrated to
±5 % at room temperature. This oscillator can be used to save power when a high clock
frequency is not needed.
In this configuration, the processor clock is derived from an external source driving the
P3.1/XTAL1 pin. The rate may be from 0 Hz up to 18 MHz. The P3.0/XTAL2 pin may be
used as a standard port pin or a clock output. When using an oscillator frequency above
12 MHz, BOE1 bit (UCFG1.5) and BOE0 bit (UCFG1.3) are required to hold the device in
reset at power-up until V
P89LPC9321 can implement clock source switch in any sources of watchdog oscillator,
7 MHz/14 MHz IRC oscillator, external clock source (external crystal or external clock
input) during code is running. CLKOK bit in CLKCON register is used to indicate the clock
switch status. CLKOK is cleared when starting clock source switch and set when
completed. Notice that when CLKOK is ‘0’, writing to CLKCON register is not allowed.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 16 November 2010
DD
8-bit microcontroller with accelerated two-clock 80C51 core
has reached its specified level.
1
⁄
2
that of the CCLK. If the clock output is not needed
P89LPC9321
© NXP B.V. 2010. All rights reserved.
DD
has reached
22 of 71